ER 25/32/40 Collets and holders

From MakerSpace Leiden
Revision as of 13:04, 11 September 2019 by DirkWillem (talk | contribs)
Jump to: navigation, search

This equipment is safety category 5: Equipment that is relatively fragile or expensive - so instructions strongly advised if you have not used them before. So getting, in person, instructions is not mandatory. Reading the wiki, and following the instructions is!

ER25 metric collet set

Set of METRIC collets -- for the ER25, ER32 and ER40 holder of theAbene VHF3 Metaalfrees machine, Metal lathe, Wood Lathe and various other MT2 taper tools.

ER 25

METRIC Sizes 1mm - 15mm -- and each will take 0.5mm for the small collets and from 6mm - 1mm smaller. So actual range is 0.5-1, 1.5-2, ... until 6 to 15mm. Do not use them outside this range. They will break (check the box with the boring bar for examples).

Label Range that fits
1 0.5 - 1 mm
2 1.5 - 2 mm
3 2.5 - 3 mm
4 3.5 - 4 mm
5 4.5 - 5 mm
6 5- 6 mm
7 6- 7 mm
8 7- 8 mm
9 8- 9 mm
10 9- 10 mm
11 10- 11 mm
12 11- 12 mm
13 12- 13 mm
14 13- 14 mm
15 14- 15 mm
16 15- 16 mm

ER 32

METRIC Sizes 10, 12, 13, 16, 18 and 20 mm. Each will take up to 1 mm smaller. So the Size 10 will accept 9-10.

The range accepted is inscribed on the top of the collet. Do not use them outside this range. They will break (check the box with the boring bar for examples).

ER 40

METRIC Sizes 23 and 26. Will fit 22-23 mm and 25-26mm. Do not exceed this range. They will break.


Make sure you `angle-click' the collet into the nut (do not force it straight). Have someone show you if you've not done it before -- as it is easy to get them out of shape this way -- causing vibration.



Inspecting the inside of our ER collet nuts reveals an internal flange that has been machined eccentric to the main axis of the nut. This is not a machining error but is designed that way to lock onto the groove of the collet and aid its release from the chuck body.

For this feature to work properly, the collet must be mounted in the nut first before fitting the assembly into the chuck body. To mount the collet in the nut, insert it on an angle, turn slightly and push it into the nut until it clicks into place on the eccentric flange. The cutter may now be fitted and the assembly tightened hard into the chuck body.

To remove the cutter, slacken and undo the nut until resistance is felt. Then, using a collet wrench, further undo the nut until the collet is released from the chuck body. Removal of the collet from the nut is the reverse of the mounting procedure.

Holders - machines

There are MT2 and ISO40 tapers for the Abene VHF3 Metaalfrees machine, Metaaldraaibank, Houtdraaibank and so on.

Holders - vice


We also have two ER25 collet holders; one square, one hex.

To hold something round in a vice; and be able to rotate it at tight/accurate angles.


Would be nice to make / find a box for them.

History & Ownership

Bought June 2019 (ER25) and September 2019 (ER32, ER40). Owned by the Stichting Makerspace Leiden.

ER25 spare nut ER25 spare nut

One spare nut bought July 2019 to replace borked one. Mail the mailing list if you use up the last spare one.


This equipment is Noise Category 3: Can be used at all hours. No limits.


Template for a box.