Difference between revisions of "Hembrug DrillPress BoorKolom PillarDrill"

From MakerSpace Leiden
Jump to: navigation, search
(Location and ownership)
Line 9: Line 9:
 
Cutting wood in the metal area is fine. Cutting metal in the wood area is frowned upon. If you do so - de-grease the machine/plateau post use !
 
Cutting wood in the metal area is fine. Cutting metal in the wood area is frowned upon. If you do so - de-grease the machine/plateau post use !
  
See also: [[Wood Drills]], [[HSS Drills]], [[Large HSS drills]] and [[Spade Drills]].
+
See also: [[Wood Drills]], [[HSS Drills]], [[Large HSS drills]] and [[Spade drills]].
  
 
== Controls ==
 
== Controls ==

Revision as of 11:12, 25 October 2021

This equipment is safety category 4:

  • In-person, instructions strongly advised but not mandatory.
  • Reading, and following, the instructions on the Wiki is mandatory!

This equipment is Noise Category 2:
Can be used at all hours, but in moderation.
Be considerate; if you feel you need to wear ear protection,
then only use the tool between 07:00 and 19:00.

safety sheet drill press

Boor-kolum, Drill press with adjustable speed (the small wheel on the left of the machine).

This is the heavier, 3-phase (Krachtstroom), version in the metal shop; there is a lighter version in the woodarea.

Cutting wood in the metal area is fine. Cutting metal in the wood area is frowned upon. If you do so - de-grease the machine/plateau post use !

See also: Wood Drills, HSS Drills, Large HSS drills and Spade drills.

Controls

  1. Handle for up/down of the head. Clockwise for down; Counterclockwise for up. Do not forget to (un)tighten handle 9.
  2. Handle for the speed.
  3. Hole through which you can see the current speed. The lower number is for "speed I" the high number for 'speed 2" (they are exactly 2x apart).
  4. Speed switch;; 0 is off, 1 is low speed and 2 is twice as fast.
  5. The normal on/off switches; prevents the machine from switching on spontaneously after a power failure -and- enforce a current limit/emergency stop.
  6. Emergency button. Do not use as an on-off button !
  7. Limiters for the travel
  8. Small scale; which you can adjust to see the travel in mm.
  9. Handle to lock vertical travel.
  10. Keyless drill chuck (taper not yet measures)


Safety

The drill press is classed as a normal, somewhat dangerous machine: instructions strongly advised but not mandatory. It can be used any hours -- but be kind to our neighbours.

Use of safety glasses will generally be needed. And the use of gloves is possible; but a mixed blessing. It increases the risk of your glove (and with it your finger) getting twisted around the drill/rotating head.

Its main risks are flying sharp bits, getting caught in something rotating or your workpiece rotating/spinning.

So clamp things well.

Changing speed

Always use the right speed; you get a nice round hole, it goes faster and the drills stay sharp. See Boorsnelheid RPM drilling speed for the speeds. See also SnijOlie BoorOlie CuttingOil

Speed is adjusted with the wheel.

Speeds and oil (metal)

There is a chart of speeds on the wall -- or see http://engineering.ucdavis.edu/wp-content/uploads/2013/08/lathespeeds.pdf

The larger your drill diameter - the lower the speed (Alu faster than steel faster than stainlesssteel/rvs); but limit countersinks/counterbores/stepdrills and similar `specials' to 200-300RPM.

There are three types of oil next to the machine. For most metals use the green oil.

Use the non-ferro oil if you find that the green oil stains your aluminiun/non-ferro metal (this is quite rare).

The third oil is generally not suitable to use with this drill press.

Safety Relay, Stop button

A safety relay was added; with a 4-6 amp current limiters along with an emergency stop button. Normal ground/earth wiring was added.

The current rotary switch does NOT allow for a switch-on block when in the wrong position. We need to find a replacement switch.

300pk

Motor

Likely [dalander switched]. We do not have a NC on the 'off' to prevent start when on.

Dalander1.png Dalander2.png

Location and ownership

Located in the metal shop. On loan; Dirk-Willem van Gulik

History

Date Descriptiopn
Q3/2021 On loan; safety relay and button added.