NodeLightsOut: verschil tussen versies

Uit MakerSpace Leiden
Ga naar: navigatie, zoeken
(Update September 2019)
(Wiring and technical data)
Regel 11: Regel 11:
 
All 3 expect AC/230 volt. The RED led on the front is the 'AartLED'.
 
All 3 expect AC/230 volt. The RED led on the front is the 'AartLED'.
  
Code in [[https://github.com/dirkx/AccesSystem/blob/master/lib-arduino/ACNode/examples/LightsOutNode/LightsOutNode.ino]]/
+
Code in [[https://github.com/dirkx/AccesSystem/blob/master/lib-arduino/ACNode/examples/LightsOutNode/LightsOutNode.ino|het git repo van de Makerspace.]].
  
 
Current mac address is '''3C:71:BF:10:62:A7''' -- wired to the top patch panel, port 23.  It is currently connected by a yellow cable to the top switch; port 23 (auto-negotiation, no further settings)
 
Current mac address is '''3C:71:BF:10:62:A7''' -- wired to the top patch panel, port 23.  It is currently connected by a yellow cable to the top switch; port 23 (auto-negotiation, no further settings)

Versie van 9 sep 2019 om 20:43


Lichten node/verklikker (photo out of date)

[OLIMEX PoE] gebaseerde node die kijkt naar de 3 AC netten van het licht.

Wiring and technical data

The 6 screw terminals are Optocoupler detect (2x3) of AC.

All 3 expect AC/230 volt. The RED led on the front is the 'AartLED'.

Code in [git repo van de Makerspace.].

Current mac address is 3C:71:BF:10:62:A7 -- wired to the top patch panel, port 23. It is currently connected by a yellow cable to the top switch; port 23 (auto-negotiation, no further settings)

Update September 2019

ESP32 PoE connector olimex

The AC voltage resistors/optocouplers have been moved out of the low voltage electronics box; and now reside in/behind the two light switches. With just 2 and 4 wires (gnd/E and signal/C of the optocouplers) going to the grey box.

White is the gnd, the colours (brown, orange, green) are the signal wires.

Furthermore GPIO 34 (was 5) has been wired to a 433 Mhz receiver - for our radio based mains-monitoring. As the digital out is 5volt - there is a simple 3k3/1k8 voltage divider to bring the signal to the 3v3 that the ESPs GPIO likes.

Building wiring

Note that the building wiring is a bit funny - an earth wire is used as a black-switch phase wire in the leftmost switch. Talk first to the trustees if you want to fix it - as this is a key part of building relative to the agreements made with the landlord.

Opto electronics

Wiring of the 3 opto couplers

Typical log

AC1 to AC3 are the OPTO couplers state; True is off (there is a pull up at work), False is AC voltage detected.

    {
      "node": "lights",
      "machine": "lights",
      "maxMqtt": 768,
      "id": "a46210bf713c",
      "ip": "192.168.3.173",
      "net": "UTP",
      "mac": "3C:71:BF:10:62:A7",
      "beat": 0,
      "approve": 0,
      "deny": 0,
      "requests": 0,
      "cache_hit": 0,
      "cache_miss": 0,
      "mqtt_reconnects": 1,
      "loop_rate": 11137.78,
      "coreTemp": 72.22222,
      "heap_free": 223272,
      "state": "Powered - no lights",
      "powered_time": 1195,
      "running_time": 0,
      "ota": true,
      "acstate1": true,
      "acstate2": true,
      "acstate3": true
   }