ToDo: verschil tussen versies

Uit MakerSpace Leiden
Ga naar: navigatie, zoeken
(recurrent)
(Blue Laser engraver/cutter)
Regel 22: Regel 22:
 
** check high voltage wiring connections to the laser tube
 
** check high voltage wiring connections to the laser tube
 
** it currently runs "test" firmware, check that buttons/motors function as they should
 
** it currently runs "test" firmware, check that buttons/motors function as they should
 +
*** (Y motor/ endstop works. X motor/endstop does not respond. User control buttons/display work.)
 
** Set max. lasertube current (2 person job for safety reasons).
 
** Set max. lasertube current (2 person job for safety reasons).
 
** once all is OK, flash "use" firmware
 
** once all is OK, flash "use" firmware

Versie van 22 apr 2019 om 21:46

We maintain the space collectively - as an all volunteer effort.

Physical things

New dust control for the wood workshop: Succobus

  • Tubing:
    • Put short pipes on each T junction behind each machine; then the Valve, then a short pipe and then a bit of hose of the right length. Secure with hose clamps. We'll need to make a few wooden/plastic adaptors on the lathe to get the diameters right.
  • Electrics:
    • Run a 3 phase cable from behind the bandsaw over the wood-storage area to the Succobus box.
    • Wire up the 3 phase with the slow-starter & wire the slowstart to the control box.
  • Collector:
    • Figure out of/how we put a thin dust collector above the separator.
    • Mount this on the wall.
    • Check if we need to remove the 90 degree angles/replace by 3x30 to get better flow.
    • See if we need to attach the separate to the wall - and het the drum 'drop' down below it.

checkout node

  • Run 3 ethernet cables to the space-door for the checkout node; and touch screen/etc.
  • Terminate the loose ethernet cable and figure out where they go.

Blue Laser engraver/cutter

  • Specialist work. Don' t undertake unless comfortable and capable. See [Blue_laser_engraver]
    • check high voltage wiring connections to the laser tube
    • it currently runs "test" firmware, check that buttons/motors function as they should
      • (Y motor/ endstop works. X motor/endstop does not respond. User control buttons/display work.)
    • Set max. lasertube current (2 person job for safety reasons).
    • once all is OK, flash "use" firmware
    • test
  • non-specialist work:
    • update [Blue_laser_engraver] (Add a picture)

floor

  • fix holes in floor in large room (with the right kind of concrete / get it somewhat level and evenly)
  • procure/find/ask shops for scraps a piece of linoleum for the small room. Same thickness, any color. About .. cm wide / .. m long. Or smaller pieces that add up. Also glue and filament (for the seams).
    • put it all in place, fixing the "gutter" in front of E-table.

lights

  • Hang the warmer lights in the small room (preferably before Hans returns! as he donated them.)
    • We might need to get cable etc. first

recurrent

  • vacuüm small room
  • And maybe the larger one too (or use a broom)
  • Dishes
  • clean kitchen
  • clean toilet
  • put bin out on the right day - volunteer in CRM

Documentation things

  • Update the wiki to describe the second garbage bin processes.
  • We have quite a few [[Category::Tools]] without foto's or where we use bland photos from HBM. To replace. Ideally in situ so you know where things are.
  • Video of an expert (e.g. HenkD) replacing & adjusting the knifes on the planer/jointer with the special tool.

Cyber Things

  • Add OpenID or similar to the CRM and push/wire this up to wordpress and the wiki.
  • Find and install crosspost module on wordpress to twitter/facebook.
  • See if we can do post-by-email or simpler for wordpress.