Difference between revisions of "Ultimaker2"

From MakerSpace Leiden
Jump to: navigation, search
(Manual and procedures)
(Reordered paragraphs for better reability)
Line 10: Line 10:
 
Both printer are operated the same. This manual is applicable to both printers.
 
Both printer are operated the same. This manual is applicable to both printers.
  
=== Characteristics of the printers ===
+
== Manual and procedures ==
 +
 +
* [[3D-printen|Software for designing and converting .stl files to printable GCODE files]]
 +
* [https://support.ultimaker.com/hc/en-us/sections/360003504360 Ultimaker Documentation]
 +
* [https://support.ultimaker.com/hc/en-us/articles/360011811480-The-Ultimaker-2-user-manuals Ultimaker Manuals]
 +
 
 +
== Characteristics of the printers ==
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
Line 22: Line 28:
 
|}
 
|}
  
=== Maintenance ===
+
== Settings ==
 
 
See [https://support.ultimaker.com/hc/en-us/sections/360003548819-Maintenance Maintenance Ultimaker 2+] for detailed descriptions on maintenance.
 
 
 
==== Recommended maintenance schedule ====
 
 
 
To keep your Ultimaker 2+ in optimal condition we recommend the following maintenance schedule, based on 1,500 printing hours per year:
 
{| class="wikitable"
 
|-
 
! Every month !! Every three months !! Every Year
 
|-
 
| Clean Printer || Check for plays on axels || Clean feeder and replace Bowden tube
 
|-
 
| Lubricate axles || Check for tension of short belts
 
|-
 
|  || Lubricate lead screw Z moto ||
 
|-
 
|  || Re-tighten hot end isolator ||
 
|}
 
 
 
==== Releasing clocked material from nozzle ====
 
Over time filament will block the nozzle. to clean the nozzle follow the following steps:
 
# Remove remaning filament
 
# Get a 30cm of Nylon filament and straighten it as much as possible
 
# Remove the blue horshoe clip underneath the white coupling
 
# Remove the filament tube out of the print head, while holding the white coupling
 
# Select in the main menu Advanced
 
# Select Heatup Nozzle
 
# Raise the nozzle temperature to 260 degrees
 
# Once on right temperature, insert the straightened piece of filament in the nozzle
 
# Set the temperature to 90 degrees and wait for the printer to reach this temperature
 
# Pull out the filament, be aware may require substantial force
 
# Repeat this process as often as required
 
 
 
See also: <br/>
 
* [https://www.youtube.com/watch?v=M2-pHgJQaI4 Automic Cleanout (Youtube)] <Br/>
 
* [https://support.3dverkstan.se/article/10-the Automic Cleanout manual]
 
 
 
=== Manual and procedures ===
 
For supplier manuals see: <Br/>
 
*
 
* [[3D-printen|Software for designing and converting .stl files to printable GCODE files]]
 
* [https://support.ultimaker.com/hc/en-us/sections/360003504360 Ultimaker Documentation] <Br/>
 
* [https://support.ultimaker.com/hc/en-us/articles/360011811480-The-Ultimaker-2-user-manuals Ultimaker Manuals]
 
 
 
==== Settings ====
 
  
 
See [https://support.ultimaker.com/hc/en-us/categories/360002336619 Materials] for description of materials which can be printed
 
See [https://support.ultimaker.com/hc/en-us/categories/360002336619 Materials] for description of materials which can be printed
Line 84: Line 45:
 
|}
 
|}
  
=== Printing on the Ultimaker 2 + or Ultimaker 2 Extended + ===
+
== Printing on the Ultimaker 2 + or Ultimaker 2 Extended + ==
  
 
To print a 3D model:
 
To print a 3D model:
Line 117: Line 78:
 
## Once the filament is removed, switch off the print with the switch on the backside of the printer
 
## Once the filament is removed, switch off the print with the switch on the backside of the printer
 
## Store filament in the appropriate location
 
## Store filament in the appropriate location
 +
 +
== Releasing clocked material from nozzle ==
 +
Over time filament will block the nozzle. to clean the nozzle follow the following steps:
 +
# Remove remaning filament
 +
# Get a 30cm of Nylon filament and straighten it as much as possible
 +
# Remove the blue horshoe clip underneath the white coupling
 +
# Remove the filament tube out of the print head, while holding the white coupling
 +
# Select in the main menu Advanced
 +
# Select Heatup Nozzle
 +
# Raise the nozzle temperature to 260 degrees
 +
# Once on right temperature, insert the straightened piece of filament in the nozzle
 +
# Set the temperature to 90 degrees and wait for the printer to reach this temperature
 +
# Pull out the filament, be aware may require substantial force
 +
# Repeat this process as often as required
 +
 +
See also: <br/>
 +
* [https://www.youtube.com/watch?v=M2-pHgJQaI4 Automic Cleanout (Youtube)] <Br/>
 +
* [https://support.3dverkstan.se/article/10-the Automic Cleanout manual]
 +
 +
== Maintenance ==
 +
 +
See [https://support.ultimaker.com/hc/en-us/sections/360003548819-Maintenance Maintenance Ultimaker 2+] for detailed descriptions on maintenance.
 +
 +
==== Recommended maintenance schedule ====
 +
 +
To keep your Ultimaker 2+ in optimal condition we recommend the following maintenance schedule, based on 1,500 printing hours per year:
 +
{| class="wikitable"
 +
|-
 +
! Every month !! Every three months !! Every Year
 +
|-
 +
| Clean Printer || Check for plays on axels || Clean feeder and replace Bowden tube
 +
|-
 +
| Lubricate axles || Check for tension of short belts
 +
|-
 +
|  || Lubricate lead screw Z moto ||
 +
|-
 +
|  || Re-tighten hot end isolator ||
 +
|}

Revision as of 13:44, 14 September 2020

This equipment is safety category 3:

  • Mandatory, in person, instructions.
  • Make sure you read the Wiki before asking.

This equipment is Noise Category 3: Can be used at all hours. No limits.

Ultimaker printers

The Makerspace has two 3D printers:

  • Ultimaker 2 +
  • Ultimaker 2 Extended +

Both printer are operated the same. This manual is applicable to both printers.

Manual and procedures

Characteristics of the printers

Property Ultimaker 2+ Ultimaker 2 Extended +
Max. size [mm] 223x223x205 223x223x305
Nozzle size 0.25, 0.4, 0.6, 0.8 0.25, 0.4, 0.6, 0.8
- - -

Settings

See Materials for description of materials which can be printed

Setting PLA ABS PETG
Printing temperature - 250 °C -
Printing table temp. - 110 °C -
Printing speed 60 mm/s 25 mm/s -
Fan speed 100% 20% -

Printing on the Ultimaker 2 + or Ultimaker 2 Extended +

To print a 3D model:

  1. Prepare the GCODE file and copy it to a SD card
    1. Enter the SD card into the SD card reader
    2. Prepare the print table for printing, apply
      1. glue (for PLA) or
      2. painters tape (for ABS)
  2. Switch on Ultimaker on the back side of the machine
  3. Change material:
    1. To change material or the enter material in to the printer, choose Material in the main menu
    2. Choose Change. The machine heats up and first will remove existing material
    3. Choose Ready once material is removed
  4. Feeding new Material
    1. Feed new material on the back side of the UltiMaker
    2. Choose Ready once the material is transported through the tube. The material will be transported to the nozzle.
    3. Wait till material flows through nozzle and confirm by selecting Ready
    4. Return to main menu by selection Return
  5. Print model
    1. Select Print
    2. Choose model you like to print. The printer heats up to the required temperature.
  6. Printing
    1. Once the nozzle and print table are at th erequired temperature, the printer will start.
    2. Printer releases small amount of filament through the nozzle
    3. The printer starts printing
    4. The display shows the expected time for the print
  7. Print ready
    1. Allow the printer table to cool down. Too early removal of the print may damage the print
    2. Remove the print from the print table
    3. Clean the printer table when required (remove glue / painter tape)
    4. Remove the Filament from the printer by executing step 3 of this procedure
    5. Once the filament is removed, switch off the print with the switch on the backside of the printer
    6. Store filament in the appropriate location

Releasing clocked material from nozzle

Over time filament will block the nozzle. to clean the nozzle follow the following steps:

  1. Remove remaning filament
  2. Get a 30cm of Nylon filament and straighten it as much as possible
  3. Remove the blue horshoe clip underneath the white coupling
  4. Remove the filament tube out of the print head, while holding the white coupling
  5. Select in the main menu Advanced
  6. Select Heatup Nozzle
  7. Raise the nozzle temperature to 260 degrees
  8. Once on right temperature, insert the straightened piece of filament in the nozzle
  9. Set the temperature to 90 degrees and wait for the printer to reach this temperature
  10. Pull out the filament, be aware may require substantial force
  11. Repeat this process as often as required

See also:

Maintenance

See Maintenance Ultimaker 2+ for detailed descriptions on maintenance.

Recommended maintenance schedule

To keep your Ultimaker 2+ in optimal condition we recommend the following maintenance schedule, based on 1,500 printing hours per year:

Every month Every three months Every Year
Clean Printer Check for plays on axels Clean feeder and replace Bowden tube
Lubricate axles Check for tension of short belts
Lubricate lead screw Z moto
Re-tighten hot end isolator