Vlakslijpmachine / Surface Grinder: verschil tussen versies

Uit MakerSpace Leiden
Ga naar: navigatie, zoeken
(Angle for dressing)
Regel 144: Regel 144:
 
[[Bestand:Jung-angle-dressing.png|600px|Slight offset for dressing with single point]]
 
[[Bestand:Jung-angle-dressing.png|600px|Slight offset for dressing with single point]]
  
Bron: https://www.nortonabrasives.com/sga-common/files/document/Catalog%20-%20Norton%20Abrasive%20Product%20Solutions%20for%20the%20Full%20Line%20Stock%20Industrial%20Market%20-%207362%20-%202017%20SADiamond.pdf
+
See the [[https://www.nortonabrasives.com/sga-common/files/document/Catalog%20-%20Norton%20Abrasive%20Product%20Solutions%20for%20the%20Full%20Line%20Stock%20Industrial%20Market%20-%207362%20-%202017%20SADiamond.pdf this document]] for more information.
 
 
Zie ook [[Diamond dresser / Ritser]].
 
 
 
=== Experimental dresser thingy ===
 
  
 
[[Bestand:Jung-angle-dressing-thing.jpg|200px|Experimental dresser thingy]]
 
[[Bestand:Jung-angle-dressing-thing.jpg|200px|Experimental dresser thingy]]
 
[[Bestand:Jung-angle-dressing-thing-2.jpg|200px|Experimental dresser thingy]]
 
[[Bestand:Jung-angle-dressing-thing-2.jpg|200px|Experimental dresser thingy]]
  
Can be placed in 4 positions and will easily click of the magchuck if things go wrong.
+
Can be placed in 4 positions and will easily click of the magchuck if things go wrong.
 +
See also the info on [[Diamond dresser / Ritser]].

Versie van 6 feb 2021 om 17:11


De machine
Specs

A late '50s, early 60's era surface grinder made by Jung. Het is mogelijk een "F40", "Serie mummer 1049" uit 1957.

For maintenance - see this page.

This equipment is safety category 2:

  • Mandatory instructions.
  • [liability waiver] on file.
  • Approval from trustees, but ok to operate alone
(but be careful/ensure you have assistance when handling very large things).


With respect to noise - be kind and considerate after 19:00 - and limit yourself to sporadic low-noise use.

This equipment is Noise Category 2:
Can be used at all hours, but in moderation.
Be considerate; if you feel you need to wear ear protection,
then only use the tool between 07:00 and 19:00.

Belangrijk bij gebruik:

  1. Autofeed naar voren werkt niet goed.
  2. Handeltje loshalen X as is lam (moet nieuw veertje in).
  3. Niet helemaal zeker of het spindel goed doorgesmeerd is
  4. Niet helemaal zeker of de leibaanoliepomp werkt.


Instructions - normal use

Manual movement

  • Make sure you have ample clearance
  • Moving X direction:
    • Flick the Y stop/end handle to release/disconnect the hydraulic pressure
    • Push the lever on the leftmost, X-wheel outward; and push the whole wheel X forward, towards the machine, to engage.
    • You can now move the table in the X direction by spinning the wheel. If this seems hard - check that you've flicked the Y stop/end handle (fair right).
  • Moving Y direction
    • Ensure that the small lever behind the Y wheel is in the middle setting.
    • Make sure that the small knob on top of the Y wheel is in the loose connection.
    • You can now use the wheel to move the table in the Y direction. If it is very stiff - check if the Y-fine adjustment dial works. If so - the small knob on top of the Y wheel is in the wrong position.
  • Moving Z direction
    • Rotate counterclockwise to lower, clockwise to raise.

Automatic movement.

  • Make sure you have ample clearance
  • Put the speed handle all the way down.
  • Set the end stops in the right places (push button on top down to slide them left/right).
  • Flick the Y stop/end handle to release/disconnect the hydraulic pressure
  • Switch the magchuck on (in the electric panel).
  • Engage the hydraulics on the electric panel (requires the magchuck to be on).
  • Press the round leather button right of the Y wheel to activate the valves.
  • Use the speed handle and rotate it gently up.

Stop by flicking the Y direction handle.

The X range is set by pressing the buttons on top of the sliders down - and moving them.

The Y step is set behind the round door - by rotating the knob inside.

The Y range is set with the stoppers at the right side of the machine; below the table. These trigger the Y stop/end handle handle.

Main Controls

Gebruik koeling

Always wait with engaging the coolant until the wheel is spinning. And stop it at the same time (or before stopping) the wheel. The reason for this is balance - if it is allowed to flow while the wheel is not spinning - the wheel wil get heavier on one side; and get out of balance.

Interlocks

De hydrauliek kan niet aan als de magneet niet aan staat. Ook al is de magneet niet in gebruik.


Temporary page to hold the data on a possible surface grinder.

Model - most likely a Jung F40 or a variation thereof.

Spindle en Slijpsteen

Slijpsteen:

  • Gat: 51mm
  • Maximale diameter: 200mm (bij 3000rpm -> 200x3.16/3000/60=35meter/seconde)
  • Maximale breedte: 16mm volgens folder (maar huidige is 20mm)


Safety

  • Document risico krachten/barsten wiel
  • Document safe-side/kickback
  • Document carbite/mask/etc risks.
  • Document alu en andere no-go/specials materials (te zacht staal)
  • Document dressing en aan de opgaande kant houden van de dresser onder hoek weg van 90 graden.
  • Document imapact koeling & wiel opstart / koeling uit voordat je het wiel stopt.

Waarschuwingen

  • Gevaar voor wegvliegende delen
  • Gevaar voor draaiende delen
  • Gevaar voor letsel aan de handen
  • Gevaar carbide
  • Pull-in (omgekeerde kickback - werkstuk klem tussen tafel en wiel als je het rechts van het midden zet).

Voorzieningen

  • Veiligheidsbril
  • Veilige kleiding
  • Spoeling
  • Kappen
  • Noodstop

Maatregelen

  • Locatie noodstop als onderdeel instructie
  • Veiligheidsbril
  • Veilige kleiding, haarnet
  • Gebruik stofmaster en spoeling bij carbinde, onderdeel instructie
  • Werken aan/vanaf de 'opgaande' kant - zodat het voorwerp zich niet tussen tafel en wiel kan trekken
  • Instructie wachten op stoppen wiel
  • Stappenplan voor in gebruik nemen nieuwe slijpsteen
  • Instructies/uitleg wat de doen bij beschadigd wiel.
  • Benadruk in koeling instructie waarom water onbalans kan geven.
  • Benadruk in instructie dat goed plat & groot genoeg essentieel zijn voor de magchuck - en laat zien hoe je met 'dingen er omheen' kan werken.

Koeling, Filter en pomp

Prior to use - check that the filter is clean/empty. Empty it after use (bag can simply be emptied into the bin).

Locatie

In de Metaalwerkplaats.

Angle for dressing

Slight offset for dressing with single point

See the [this document] for more information.

Experimental dresser thingy Experimental dresser thingy

Can be placed in 4 positions and will easily click of the magchuck if things go wrong. See also the info on Diamond dresser / Ritser.