Vlakslijpmachine / Surface Grinder: verschil tussen versies

Uit MakerSpace Leiden
Ga naar: navigatie, zoeken
(Interlocks)
(5 tussenliggende versies door dezelfde gebruiker niet weergegeven)
Regel 4: Regel 4:
  
 
[[Bestand:Jung-f40-asis.jpg|miniatuur|De machine]]
 
[[Bestand:Jung-f40-asis.jpg|miniatuur|De machine]]
 +
[[Bestand:Jung-ssheet.pdf|miniatuur |Safetysheet Jung Surfacegrinder / Vlakslijpmachine]]
 
[[Bestand:Jung-specs.png|miniatuur|Specs]]
 
[[Bestand:Jung-specs.png|miniatuur|Specs]]
  
Regel 10: Regel 11:
 
{{SafetyCat2}}
 
{{SafetyCat2}}
 
{{NoiseCat2}}
 
{{NoiseCat2}}
 +
  
 
'''Belangrijk bij gebruik:
 
'''Belangrijk bij gebruik:
Regel 64: Regel 66:
  
 
De hydrauliek kan niet aan als de magneet niet aan staat. Ook al is de magneet niet in gebruik.
 
De hydrauliek kan niet aan als de magneet niet aan staat. Ook al is de magneet niet in gebruik.
 
<gallery>
 
jung-1.jpg|Valkslijpmachine
 
jung-2.jpg| Valkslijpmachine
 
jung-3.jpg| Valkslijpmachine
 
jung-4.jpg| Valkslijpmachine
 
jung-5.jpg| Valkslijpmachine
 
jung-6.jpg| Valkslijpmachine
 
</gallery>
 
  
 
== Spindle en Slijpsteen ==
 
== Spindle en Slijpsteen ==
Regel 90: Regel 83:
 
* Carbite/mask/etc risks.
 
* Carbite/mask/etc risks.
  
* Risico van Alu en andere no-go/specials materials (te zacht staal)
+
* [http://web.mit.edu/course/other/machineshop/Grinder/aluminum.html Risico] [https://www.bladesmithsforum.com/index.php?/topic/8855-aluminumsteel-grindings-how-dangerous/#comment-79920_wrap van aluminium] en andere no-go/specials materials (te zacht staal)
  
 
* Document dressing en aan de opgaande kant houden van de dresser onder hoek weg van 90 graden.
 
* Document dressing en aan de opgaande kant houden van de dresser onder hoek weg van 90 graden.

Versie van 15 feb 2021 om 21:02


De machine
Safetysheet Jung Surfacegrinder / Vlakslijpmachine
Specs

A late '50s, early 60's era surface grinder made by Jung. For maintenance - see this page.

This equipment is safety category 2:

  • Mandatory instructions.
  • [liability waiver] on file.
  • Approval from trustees, but ok to operate alone
(but be careful/ensure you have assistance when handling very large things).


With respect to noise - be kind and considerate after 19:00 - and limit yourself to sporadic low-noise use.

This equipment is Noise Category 2:
Can be used at all hours, but in moderation.
Be considerate; if you feel you need to wear ear protection,
then only use the tool between 07:00 and 19:00.


Belangrijk bij gebruik:

  1. Autofeed naar voren werkt niet goed.
  2. Handeltje loshalen X as is lam (moet nieuw veertje in).
  3. Niet helemaal zeker of het spindel goed doorgesmeerd is
  4. Niet helemaal zeker of de leibaanoliepomp werkt.


Instructions - normal use

Manual movement

  • Make sure you have ample clearance
  • Moving X direction:
    • Flick the Y stop/end handle to release/disconnect the hydraulic pressure
    • Push the lever on the leftmost, X-wheel outward; and push the whole wheel X forward, towards the machine, to engage.
    • You can now move the table in the X direction by spinning the wheel. If this seems hard - check that you've flicked the Y stop/end handle (fair right).
  • Moving Y direction
    • Ensure that the small lever behind the Y wheel is in the middle setting.
    • Make sure that the small knob on top of the Y wheel is in the loose connection.
    • You can now use the wheel to move the table in the Y direction. If it is very stiff - check if the Y-fine adjustment dial works. If so - the small knob on top of the Y wheel is in the wrong position.
  • Moving Z direction
    • Rotate counterclockwise to lower, clockwise to raise.

Automatic movement.

  • Make sure you have ample clearance
  • Put the speed handle all the way down.
  • Set the end stops in the right places (push button on top down to slide them left/right).
  • Flick the Y stop/end handle to release/disconnect the hydraulic pressure
  • Switch the magchuck on (in the electric panel).
  • Engage the hydraulics on the electric panel (requires the magchuck to be on).
  • Press the round leather button right of the Y wheel to activate the valves.
  • Use the speed handle and rotate it gently up.

Stop by flicking the Y direction handle.

The X range is set by pressing the buttons on top of the sliders down - and moving them.

The Y step is set behind the round door - by rotating the knob inside.

The Y range is set with the stoppers at the right side of the machine; below the table. These trigger the Y stop/end handle handle.

Main Controls

Gebruik koeling

Always wait with engaging the coolant until the wheel is spinning. And stop it at the same time (or before stopping) the wheel. The reason for this is balance - if it is allowed to flow while the wheel is not spinning - the wheel wil get heavier on one side; and get out of balance.

Interlocks

De hydrauliek kan niet aan als de magneet niet aan staat. Ook al is de magneet niet in gebruik.

Spindle en Slijpsteen

Slijpsteen:

  • Gat: 51mm
  • Maximale diameter: 200mm (bij 3000rpm -> 200x3.16/3000/60=35meter/seconde)
  • Maximale breedte: 16mm volgens folder (maar huidige is 20mm)


Safety / Risico's

  • Risico krachten/barsten wiel
  • Risico kickback, bestaan safe-side
  • Carbite/mask/etc risks.
  • Document dressing en aan de opgaande kant houden van de dresser onder hoek weg van 90 graden.
  • Document impact koeling & wiel opstart / koeling uit voordat je het wiel stopt.
  • Risico unbalance/uneven dressing/unbalanced mounting
  • Need for the covers to be on
  • Safe operator position & sufficient room, Risk of pinching, etc.
  • Slippery objects/floor due to coolant spill
  • Debris/dust/etc

Waarschuwingen

  • Gevaar voor wegvliegende delen
  • Gevaar voor draaiende delen
  • Gevaar voor letsel aan de handen
  • Gevaar carbide
  • Pull-in (omgekeerde kickback - werkstuk klem tussen tafel en wiel als je het rechts van het midden zet).

Don'ts =

  • Do not strike the wheel against the material as this action could cause faults in the wheel.
  • Do not clean the magnetic chuck or mount or remove work until the wheel has completely stopped.
  • Do not start the machine until the wheel guard is in place.
  • Do not stand left or right from grinding wheel when starting a grinder (or have hands there). Stand in the operator position.
  • Do not apply work too quickly to a cold wheel or disk.
  • Do not jam work into the wheel.
  • Never reach above or around a moving wheel.

Voorzieningen

  • Veiligheidsbril
  • Veilige kleiding
  • Spoeling
  • Kappen
  • Noodstop
  • Juiste positie

Maatregelen

  • Locatie noodstop als onderdeel instructie
  • Veiligheidsbril
  • Veilige kleiding, haarnet
  • Gebruik stofmaster en spoeling bij carbinde, onderdeel instructie
  • Werken aan/vanaf de 'opgaande' kant - zodat het voorwerp zich niet tussen tafel en wiel kan trekken
  • Instructie wachten op stoppen wiel
  • Stappenplan voor in gebruik nemen nieuwe slijpsteen
  • Instructies/uitleg wat de doen bij beschadigd wiel.
  • Benadruk in koeling instructie waarom water onbalans kan geven.
  • Benadruk in instructie dat goed plat & groot genoeg essentieel zijn voor de magchuck - en laat zien hoe je met 'dingen er omheen' kan werken.

Koeling, Filter en pomp

Prior to use - check that the filter is clean/empty. Empty it after use (bag can simply be emptied into the bin).

Locatie

In de Metaalwerkplaats.

Angle for dressing

Slight offset for dressing with single point

See this norton guide for more information.

Experimental dresser thingy Experimental dresser thingy Experimental dresser thingy

Can be placed in 4 positions and will easily click of the magchuck if things go wrong. See also the info on Diamond dresser / Ritser.

History

Datum Wie Wat
2020-12 dirkx Nieuwe druklagers hydrauliek
2021-1 dirkx Leibaanolie ververst
2021-1-20 dirkx Koelmiddel ververst.
2021-1-5 dirkx 2x nieuwe diamand ritsers
2021-2-1 dirkx Nieuwe pomp, nieuwe slangen, nieuwe schakelaars