Jigs (wood)
This page regroups information about custom made jigs for various machines of the wood workshop.
Inhoud
Table Saw jigs
Rod maker (table saw lathe)
The purpose of this jig is to create straight, cylindrical rods of wood, between ~20mm and ~90mm diameter, up to 65 cm in length, i.e. longer than what you can do with the wood lathe.
Material preparation
In order to make the operation safer and faster, it is a good idea to remove some material from your stock piece first. Start by cutting your stock quare, with a section ~2mm larger than the final diameter of the rod. Once you have a square section, cut the corners off with the table saw blade tilted 45 degrees, giving you an octogonal section.\ Find the center of your stock on both ends. Drill a 15mm deep pilot hole with a 4mm bit, and then do the same operation with a 7.5mm bit.
Table saw preparation
In order to operate the jig, it is necessary to remove the riving knife of the table saw, located behind the saw blade.
You can remove the riving knife by loosening the bolts with a 19mm wrench.
Jig setup
Mount your stock piece on the jig, making sure to tighten a nut against each end of the world piece to prevent the rod from pulling the bolts when it starts rotating. Make sure the rod can spin freely and tighten the nuts securing the moving end of the jig. Prepare a drill with a 13mm socket and an extended bit holder. The extended bit holder is a very important safety aspect, as it keeps your fingers away from the blade when it reaches the end of the stock close to you.
Operation
It is important to take only very small passes in order not to sideload the blade. Move the jig slowly while you spin the rod with the drill (and white the table saw is running of course) Be careful that the jig does not tip over. Control the the diameter on both ends regularly and use shims under the adjustable end if necessary. When measuring, always turn off the saw.
Picture frame jig
This jig aim at providing highly accurate and repeatable litter (45degrees) cuts for building picture frames.
Table saw preparation
The key is to setup the blade to be perfectly 90° to the table. Do not trust the inclination mechanism, use an machinist square to check for squareness.
Material preparation
The exact profile for a picture frame to be used largely depends on your need and personal preferences. However it almost always consists of a L shaped profile. To make it, start from a square stock and using two table cuts, bremove some material for the glass, at work, backer panel etc...
Operation
The jig is used in a two-step process, as follows:
- The first operation consists in cutting the first mitter, there is no need to measure anything. Start by placing your stock piece (ie frame profile) on the left side of the jig and hold it firmly, making sure your fingers are far from the blade. Using the wood handle, slowly push the jig forward to make the first cut.
- The second operation consists in cutting the piece to the correct length. Measure and draw a line on your piece to the desired length. Take a scrap piece of wood and clamp it to the guide, in order to create a positive stop, making sure the pencil mark coincides with the edge of the kerf cut in the middle of the jig. It very important that you use the positive stop for all the pieces which are supposed of the same length. Measuring is significantly less repeatable than using a positive stop. Make sure that the side of the piece which was against the guide on the left in the previous step is the same one against the guide on the right in this second step.
A few points :
- Make sure there is no sawdust on the edge of either left of right profile
- The masking tape has been added for fine tuning, please don't remove it
- Operation of the jig will be much smoother if some dry lubricant has been applied to the table beforehand (bottom right of the paint cupboard)
Glue up
Once the pieces have been cut, align them against a straight edge (can be the router table fence for instance) and join the pieces with masking tape. Spread some glue on the mitter faces and fold the frame, using an extra piece of tape to close it. It is advised to use a band clamp (in the cupboard under the lathe in the right compartment) for additional clamping pressure.