Abene Metal Mill / Freesbank: verschil tussen versies
(→Current situation) |
(→Disassembly Notes) |
||
Regel 53: | Regel 53: | ||
= Disassembly Notes = | = Disassembly Notes = | ||
+ | |||
+ | #. When removing the X table - either remove the spindle first -or- make sure that when you put the X table on a cart you use blocks to not bend the then very exposed spindle. | ||
+ | #. When removing the gearbox in the knee it is *crucial* to first remove the guiding pin. This allows you to rotate the unit some 10 degrees clockwise to lift the crownwheel. You *will* break a teeth from the crownwheel otherwise ! |
Versie van 16 dec 2017 om 14:23
Inhoud
Abene VHF3 Metaalfrees machine
See github for documentation. [1]
Status
Not yet operational Unresolved issues are:
- . Classification of the machine
- . Instructions and safety card.
To procure/find
- . Power indicator light (115Volt, E14 bulb)
- . Power indicator on the current-limiter (230Volt, E10).
- . ISO 40 with drill chuck. Or MT4/ISO40 in which the chuck of the lathe would fit (perhaps HBM 02594)
- . Small spanner number 14 for the taper bolt.
- . Light - e.g. https://nl.aliexpress.com/item/1-Pcs-900LM-Mini-6-Inch-12W-4-X-3W-Car-LED-Light-Bar-as-Worklight/32824998138.html on a flexible arm.
Very optional:
- . Set of ER32 collets for ISO 40 or similar.
- . Mounting fixtures e.g. a simple version of http://www.fritshansen.nl/winkel/gereedschappen/opspanset-t-120-52-delig/
To make/find
- . T-Slot cleaning jig.
Lubrication History
Details on github: [2]
The actual advice from Abene is much simpler:
- Q8 Goya NT68 (gear oil) spindle and feed gear box)
- For everything else, Q8 Wagner NT68 (Slideway lube)
Current situation
- . Main drive gearbox, spindle gearbox, drive gearbox on the left.
- . Replaced with Hykrol HLP ISO-VG 100 (ISO 100 hydraulic oil), 2017-11-19. 5L was about sufficient all 3 gearboxes.
- . Overarm bearing
- . Emptied and cleaned 2017-11-19. Not yet replaced.
- . Sideways
- . Emptied and cleaned 2017-11-12. Replaced by sideway oil 68 - 2017-12-15.
- . Kneejacking screw
- . Emptied and cleaned 2017-11-29. Replaced by ISO 46 hydraulic oi.l 2017-11-29.
- . Headstock and motor bearings.
- . Emptied and cleaned. 2017-11-29. Replaced by ISO 100 hydraulic oil. 2017-11-29.
- . Coolant
- . Emptied and cleaned - not able to reach all parts. Replaced by 1:10 mix. 2017-12-15. Zie"http://www.oliehandel.nl/eurol/eurol-boorolie-a" voor details.
Disassembly Notes
- . When removing the X table - either remove the spindle first -or- make sure that when you put the X table on a cart you use blocks to not bend the then very exposed spindle.
- . When removing the gearbox in the knee it is *crucial* to first remove the guiding pin. This allows you to rotate the unit some 10 degrees clockwise to lift the crownwheel. You *will* break a teeth from the crownwheel otherwise !