Simple Box Making: verschil tussen versies
(Nieuwe pagina aangemaakt met 'Category:Docu Simple box making (notes to stop myself from re-inventing this) # Find a rectangular piece of plywood # Measure width - divide by 3 (this will...') |
|||
| (7 tussenliggende versies door 3 gebruikers niet weergegeven) | |||
| Regel 1: | Regel 1: | ||
| − | [[Category: | + | [[Category:Tutorials]] |
| − | |||
Simple box making (notes to stop myself from re-inventing this) | Simple box making (notes to stop myself from re-inventing this) | ||
# Find a rectangular piece of plywood | # Find a rectangular piece of plywood | ||
| − | |||
# Measure width - divide by 3 (this will be the -height- of the box) | # Measure width - divide by 3 (this will be the -height- of the box) | ||
| − | |||
# Set this width on the table saw (clean with) | # Set this width on the table saw (clean with) | ||
| − | + | # Saw length wise. So the last strip will in fact be smaller than the first two. That is good - it needs to be the the width of the box minus the thickness of the wood. | |
| − | # Saw length wise. So the last strip will in fact be smaller than the first two. | ||
| − | |||
# Cut, from each strip; one piece the length of the box (back to back). Generally you can do this twice; for two boxes. | # Cut, from each strip; one piece the length of the box (back to back). Generally you can do this twice; for two boxes. | ||
| − | |||
# Cut from the two wider strips; two square pieces. Generally you can do this twice; for two boxes. | # Cut from the two wider strips; two square pieces. Generally you can do this twice; for two boxes. | ||
| − | |||
# Adjust the height of the tablesaw to half the tickness of the plywood. Adjust the distance to be half as wel. | # Adjust the height of the tablesaw to half the tickness of the plywood. Adjust the distance to be half as wel. | ||
| + | # Make the flat cuts and the perpendicular cuts. | ||
| + | # Finally, if needed - adjust the width of the bottom piece. | ||
| − | + | [[Bestand:simple-box.png]] | |
| − | # | + | # Optional: Use a spade drill (20-25mm) to dril two holes in the fronts as a handle |
| + | # Optional: Route these to get them nice and round. | ||
| + | # Optional: Glue two strips of wood about halfway on the long ends - to support a sub-drawer/box. | ||
| + | # Glue the bits together; use the nailgun to keep them fixed while the glue dries. | ||
Huidige versie van 16 nov 2024 om 23:52
Simple box making (notes to stop myself from re-inventing this)
- Find a rectangular piece of plywood
- Measure width - divide by 3 (this will be the -height- of the box)
- Set this width on the table saw (clean with)
- Saw length wise. So the last strip will in fact be smaller than the first two. That is good - it needs to be the the width of the box minus the thickness of the wood.
- Cut, from each strip; one piece the length of the box (back to back). Generally you can do this twice; for two boxes.
- Cut from the two wider strips; two square pieces. Generally you can do this twice; for two boxes.
- Adjust the height of the tablesaw to half the tickness of the plywood. Adjust the distance to be half as wel.
- Make the flat cuts and the perpendicular cuts.
- Finally, if needed - adjust the width of the bottom piece.
- Optional: Use a spade drill (20-25mm) to dril two holes in the fronts as a handle
- Optional: Route these to get them nice and round.
- Optional: Glue two strips of wood about halfway on the long ends - to support a sub-drawer/box.
- Glue the bits together; use the nailgun to keep them fixed while the glue dries.
