Node Tussendeur: verschil tussen versies
(→current and solenoid) |
|||
| (15 tussenliggende versies door dezelfde gebruiker niet weergegeven) | |||
| Regel 10: | Regel 10: | ||
|- | |- | ||
| Logging || | | Logging || | ||
| − | + | [[telnet://192.168.6.160 telnet]], | |
serial 8N1, 115200, | serial 8N1, 115200, | ||
| − | + | [[http://192.168.6.160 http]], | |
| − | + | [[mqtt:///#ac/log/tussendeur mqtt]] and syslog to the space local server. | |
|} | |} | ||
| + | |||
| + | You need to be on the local LAN/Wifi of the space to be able to use the above telnet and http links. | ||
= Normal operation = | = Normal operation = | ||
| Regel 82: | Regel 84: | ||
== Board jumpers and settings == | == Board jumpers and settings == | ||
| − | [[Bestand:Nodetussendeur-jumpers-diode.jpg|miniatuur|Note diode and red/black wire to bring 12v to the solenoid]] | + | [[Bestand:Nodetussendeur-jumpers-diode.jpg|miniatuur|Note diode and red/black wire to bring 12v to the solenoid, blusdiode over solenoid]] |
=== Board - Serial #5 === | === Board - Serial #5 === | ||
| Regel 161: | Regel 163: | ||
https://github.com/MakerSpaceLeiden/AccessSystem/lib-arduino/ACNode/examples/TussendeurNode | https://github.com/MakerSpaceLeiden/AccessSystem/lib-arduino/ACNode/examples/TussendeurNode | ||
| + | |||
| + | Tag as pushed ```tussendeur-2024-12-01```` | ||
= Bill of material = | = Bill of material = | ||
| Regel 183: | Regel 187: | ||
|- | |- | ||
| Buzzer x1 || ~0.50€ | | Buzzer x1 || ~0.50€ | ||
| + | |- | ||
| + | | Busdiode, 1N6303A x1 || ~0.05€ | ||
|- | |- | ||
| RJ12 socket x 2 || ~1.00 | | RJ12 socket x 2 || ~1.00 | ||
| Regel 188: | Regel 194: | ||
| RJ12 plug x 2 || ~1.00 | | RJ12 plug x 2 || ~1.00 | ||
|- | |- | ||
| − | | Extra super big capacitor | + | | Extra super big capacitor || free, donated to MSL |
|- | |- | ||
| 12v coil relay; switch 240ACV/3A || free, donated to MSL | | 12v coil relay; switch 240ACV/3A || free, donated to MSL | ||
| Regel 195: | Regel 201: | ||
= History = | = History = | ||
| − | + | {| class="wikitable" | |
| − | Rebuild | + | |- |
| − | + | ! Datum / Date!! Description | |
| − | + | |- | |
| − | + | | 2016 || Rebuild | |
| − | + | |- | |
| + | | Early 2018 || upgradedwith the 1.1 batch (yellow boards) | ||
| + | |- | ||
| + | | 2022/2/19 || [[https://github.com/MakerSpaceLeiden/AccesSystem/releases/tag/cache-fix-2022-02-19-1.00 Firmware last updated]] - to fix caching and a range of errors found by Duco when using the Arduino rather than the VisualStudio setup. | ||
| + | |- | ||
| + | | 2024-12-01 || replaced by a the black variation of [[PowerNode White]] - software tag tussendeur-2024-12-01 | ||
| + | |- | ||
| + | | 2024-12-07 || Solenoid replaced by Alex; one spare bought. | ||
| + | |- | ||
| + | |} | ||
Huidige versie van 19 dec 2024 om 22:10
| IP address | ? 192.168.6.160 |
| hardware ethernet | 08:D1:F9:90:B3:63 (wired) |
| Logging |
[telnet], serial 8N1, 115200, [http], mqtt:///#ac/log/tussendeur mqtt and syslog to the space local server. |
You need to be on the local LAN/Wifi of the space to be able to use the above telnet and http links.
Inhoud
Normal operation
Swipe your card - node should beeb for 4 seconds; or give a short intermittent deny signal.
Bypassing the node
With the explicit permission from a trustee - a node can be bypassed. For example when it is broken. There is a red dip switch on the back of the board; near the AC/DC transformer and the fuse.
Placing it in the 'on' position will bypass the node (i.e. to the left in the picture); and provided power to the solenoid.
Obviously - doing so without the express permission is a sure way to loose your membership.
Trouble Shooting
Check what is on the display. The first QR code will bring you to this page. The second QR code will show you the logs in a browser. You can also telnet to the IP address shown in the 'MORE' display to see the log in real time.
See this page for more details.
Swipe ok - but does not want to open door
- Do you see waiting for card on the display ? If so - it has not read your card (yet).
- Did you hear one or more beebs when you swiped ? If so - your card is picked up ok ?
If you hear beebs:
- Did you hear 3 or more beeps when you swiped ? If so - your card is not getting permission from the system.
- Does your personal page in mijn.makerspaceleiden.nl show that you have permission ?
- Did you get your permissions quite recently ?
- Is the internet in the space up and running (as it only periodically updates its database).
The Machine does not want to accept my badge
- Do you hear a beeb when swiping ? If so - it has read your card -- and see above issues.
If it did not beeb:
- Did it work on the door ?
- Does it work on any other machine ?
If so - your badge is fine - but we may have a broken ACNode or a broken reader. Report this to the mailing list - or if you know a little of IT and electronics - go to the troubleshooting section and connect to the log via your webbrowser or via telnet. Then swipe again and see what really happens.
Note that we are, at this time, not sure if these nodes will survive the welding area.
Resetting the Node
Unplug the ethernet cable in the main patch cabinet. See this page for details.
Wait at least 60 seconds until you try again (the ESP32 is quite slow & it needs to create some cryptographic date before it can start communicating over https/SSL).
Electronics
De node is PoE powered; set to 12 Volt.
rfid scanner
The middle section is broken out and, with an 6 wire, RJ12 socketed (ISDN) wire, interconnected.
So the main PCB is inside; the RDID bit is outside. The wire carries i2c, 3v3 power and the 2 reset/IRQ signals.
The wiring is straight; RJ12 wiring:
Board jumpers and settings
Board - Serial #5
- Rework 1 - verwijderen ESD diodes antenne
- Rework 2 - omdraaien transistors programmering
- 0-ohm (jumpering) R109 removed; 5V of USB not connected to 5V rail.
- Fixed 5v resistor replaced by potentionmeter; and set to 7 (was12) Volt
Jumpers:
- Vpoe - set to 'Slow Start'
- Vpoe5 - set 'Slow Start'
- Vpwr - set to 'Vpoe' as source.
- 5V- set to 'Vpoe5' as source.
- Out2 - via the two AC jumpers
Special Wiring
The 12 volt DC of VPoe is wired to L/N of the normal 220V AC input. So that the C/NO of relay 2 is a simple 12 volt on/off.
There is an extra diode wired across the coil-wires.
Connectors
Green Connector
Only the bottom 2 sockets are needed/switched - and can be wired 1:1 to the solenoid.
| PIN | Description | Use |
|---|---|---|
| 1 | CUR2 | NC |
| 2 | CUR2 | NC |
| 3 | OPTO 4 | NC |
| 4 | OPTO 3 | NC |
| 5 | OPTO 2 | NC |
| 6 | OPTO 2 | NC |
| 7 | OPTO 1 | NC |
| 8 | OPTO 1 | NC |
| 9 | L input | L; 12 Volt out |
| 10 | N input | N; GND |
| 11 | Relay 1 NO | NC |
| 12 | Relay 1 Common | NC |
| 13 | Relay 1 NC | NA |
| 14 | Relay 1 NC | 12 volt to solenoid |
| 15 | Relay 1 common | 12 volt from solenoid |
current and solenoid
Somehow the solenoids current increases at 12Volt to a point where it needs well over 30 watt. At which point the PoE switch current protection trips.
Solved for now by reducing the voltage to about 7 volt. No trips observed since.
Gele draad RJ12/6 aderige kabel naar de buiten RFID scanner. Witte kabel met RJ45 stekker - ethernet; Grijze kabel met groene stekkertje - naar Solenoid.
Zaak hangt nu in het kastje.
Source code
https://github.com/MakerSpaceLeiden/AccessSystem/lib-arduino/ACNode/examples/TussendeurNode
Tag as pushed ```tussendeur-2024-12-01````
Bill of material
| Back v1.11 node board | ~35 |
| ESP32 | ~3.50 |
| Small green Connector | ~0.20€ |
| RJ45 connector | ~0.10 |
| Solenoid 12V door | ~39€ |
| OLED display | ~3.50€ |
| Buttons x3 | ~0.30€ |
| Buzzer x1 | ~0.50€ |
| Busdiode, 1N6303A x1 | ~0.05€ |
| RJ12 socket x 2 | ~1.00 |
| RJ12 plug x 2 | ~1.00 |
| Extra super big capacitor | free, donated to MSL |
| 12v coil relay; switch 240ACV/3A | free, donated to MSL |
History
| Datum / Date | Description |
|---|---|
| 2016 | Rebuild |
| Early 2018 | upgradedwith the 1.1 batch (yellow boards) |
| 2022/2/19 | [Firmware last updated] - to fix caching and a range of errors found by Duco when using the Arduino rather than the VisualStudio setup. |
| 2024-12-01 | replaced by a the black variation of PowerNode White - software tag tussendeur-2024-12-01 |
| 2024-12-07 | Solenoid replaced by Alex; one spare bought. |
