Node Wood Lathe: verschil tussen versies
(→Trouble shooting) |
|||
| (7 tussenliggende versies door 2 gebruikers niet weergegeven) | |||
| Regel 1: | Regel 1: | ||
| − | [[ | + | [[Category:Nodes & network devices]] |
| − | [[Bestand: | + | [[Bestand:Woodnode01.jpg|200px]] |
| − | [[Bestand: | + | [[Bestand:Woodnode02.jpg|200px]] |
| + | [[Bestand:Woodnode03.jpg|200px]] | ||
| + | [[Bestand:Woodnode04.jpg|200px]] | ||
PoE node voor the woodlathe based on a [[PowerNode White]]. | PoE node voor the woodlathe based on a [[PowerNode White]]. | ||
| Regel 23: | Regel 25: | ||
== Configuration == | == Configuration == | ||
| − | The unit contains a PoE fed [[PowerNode White]] that is on Ethernet (LAN). It has a single relay that simply turns one of the phases (L) on and off. The button is wired to 'menu' and contains a LED. This LED is wired to 'ERR'. One of the feeding wires is strung through the Current coil. The relay is 5Volt. | + | The unit contains a PoE fed [[PowerNode White]] that is on Ethernet (LAN). It has a single relay that simply turns one of the phases (L) on and off. The button is wired to 'menu' and contains a LED. This LED is wired to 'ERR'. One of the feeding wires is strung through the Current coil. All this runs through the connector. The relay is 5Volt. |
| + | |||
| + | [[Bestand:Woodnode05.jpg|200px]] | ||
| + | [[Bestand:Woodnode06.jpg|200px]] | ||
The software can be found in ACNode its examples (in the Arduino IDE) or on [https://github.com/MakerSpaceLeiden/AccesSystem/blob/master/lib-arduino/ACNode/examples/WoodLatheNode/WoodLatheNode.ino GitHub]. | The software can be found in ACNode its examples (in the Arduino IDE) or on [https://github.com/MakerSpaceLeiden/AccesSystem/blob/master/lib-arduino/ACNode/examples/WoodLatheNode/WoodLatheNode.ino GitHub]. | ||
| Regel 78: | Regel 83: | ||
"fw": "ACNode/examples/WoodLatheNode/WoodLatheNode.ino Jan 1 2024 17:45:18" | "fw": "ACNode/examples/WoodLatheNode/WoodLatheNode.ino Jan 1 2024 17:45:18" | ||
} | } | ||
| + | |||
| + | == History == | ||
| + | |||
| + | Latest incarnation installed late 2023. | ||
| + | |||
| + | [[Bestand:Woodnode.jpg|miniatuur| Old node, no longer in use]] | ||
| + | [[Bestand:WoodnodeInside.jpg|miniatuur|Old node, no longer in use]] | ||
Huidige versie van 16 nov 2024 om 23:07
PoE node voor the woodlathe based on a PowerNode White.
Use
When stationaly - led will flash briefly every few seconds. If it flashes faster - it is unhappy about something.
Swipe your card at the bottom. LED wil come on solid (or flash rapidly during check or error).
Operate the machine with the red/green on-off button on the right end / near the legs.
Press orange button once you are done to lock things. Note: the unit will refuse to power off while the machine is running. So first power off the machine with its own red/green button (press green). Then press the button on the node to `lock' it.
Trouble shooting
See PowerNode White for details.
The log file is available on http://woodlathe.local/ or http://192.168.6.144/. One can also telnet to this address. Logs are also sent to MQTT and to Syslog at the firewall. Or connect a serial cable; but be sure to use a Galvanic USB isolator.
Configuration
The unit contains a PoE fed PowerNode White that is on Ethernet (LAN). It has a single relay that simply turns one of the phases (L) on and off. The button is wired to 'menu' and contains a LED. This LED is wired to 'ERR'. One of the feeding wires is strung through the Current coil. All this runs through the connector. The relay is 5Volt.
The software can be found in ACNode its examples (in the Arduino IDE) or on GitHub.
Log
Thu Jan 23 13:55:07 CET 2020 ac/log/woodlathe woodlathe {
{
"manual_poweroff": 0,
"idle_poweroff": 0,
"errors": 0,
"ota": true,
"node": "woodlathe",
"machine": "woodlathe",
"maxMqtt": 384,
"id": "887124a4ae30",
"ip": "192.168.6.144",
"net": "UTP",
"mac": "30:AE:A4:24:71:8B",
"beat": 1704134479,
"alive-uptime": 6600,
"approve": 1,
"deny": 0,
"requests": 1,
"cache_hit": 1,
"cache_miss": 0,
"cache_purge": 0,
"cache_update": 1,
"mqtt_reconnects": 1,
"loop_rate": 15.1384325,
"coreTemp": 53.33333333,
"heap_free": 168180,
"rfid_scans": 1,
"rfid_misses": 103951,
"rfid": "RFID-MFRC522",
"state": "Waiting for card, screen dark",
"seconds_in_state": [
0,
3,
0,
0,
0,
1244,
0,
0,
0,
5645,
0,
2,
3,
0
],
"normal_poweroff": 1,
"fw": "ACNode/examples/WoodLatheNode/WoodLatheNode.ino Jan 1 2024 17:45:18"
}
History
Latest incarnation installed late 2023.
