Abene VHF3 Metaalfrees machine

Abene VHF3 Metaalfrees machine

See github for documentation. [1]

Status

Not yet operational Unresolved issues are:

1. . Classification of the machine
2. . Instructions and safety card.

To procure/find

1. . Power indicator light (115Volt, E14 bulb)
2. . Power indicator on the current-limiter (230Volt, E10).
3. . ISO 40 with drill chuck. Or MT4/ISO40 in which the chuck of the lathe would fit (perhaps HBM 02594)
4. . Small spanner number 14 for the taper bolt.
5. . Light - e.g. https://nl.aliexpress.com/item/1-Pcs-900LM-Mini-6-Inch-12W-4-X-3W-Car-LED-Light-Bar-as-Worklight/32824998138.html on a flexible arm.

Very optional:

1. . Set of ER32 collets for ISO 40 or similar.
2. . Mounting fixtures e.g. a simple version of http://www.fritshansen.nl/winkel/gereedschappen/opspanset-t-120-52-delig/

To make/find or buy

1. T-Slot cleaning jig. i.e some wood/plastic shaped like http://www.wttool.com/index/page/product/product_id/19972/product_name/RDX+T-Slot+Cleaner&update_continue_shopping=true?utm_medium=cpc&utm_source=SiteChampion

1. ISO 40 fixture. E.g. a copy of https://www.ebay.com/itm/CAT-40-Tool-Holder-Tightening-Fixture-with-thumb-screw-/252418335037 https://www.wgm-maschinen.de/Zubehoer/Spannwerkzeuge/Bernardo-Montagestand-ISO-40.html

Lubrication History

Details on github: [2]

The actual advice from Abene is much simpler:

1. Q8 Goya NT68 (gear oil) spindle and feed gear box)
2. For everything else, Q8 Wagner NT68 (Slideway lube)

Current situation

1. . Main drive gearbox, spindle gearbox, drive gearbox on the left.
   1. . Replaced with Hykrol HLP ISO-VG 100 (ISO 100 hydraulic oil), 2017-11-19. 5L was about sufficient all 3 gearboxes.
2. . Overarm bearing
   1. . Emptied and cleaned 2017-11-19. Not yet replaced.
3. . Sideways
   1. . Emptied and cleaned 2017-11-12. Replaced by sideway oil 68 - 2017-12-15.
4. . Kneejacking screw
   1. . Emptied and cleaned 2017-11-29. Replaced by ISO 46 hydraulic oi.l 2017-11-29.
5. . Headstock and motor bearings.
   1. . Emptied and cleaned. 2017-11-29. Replaced by ISO 100 hydraulic oil. 2017-11-29.
6. . Coolant
   1. . Emptied and cleaned - not able to reach all parts. Replaced by 1:10 mix. 2017-12-15. Zie"http://www.oliehandel.nl/eurol/eurol-boorolie-a" voor details.

Disassembly Notes

1. . When removing the X table - either remove the spindle first -or- make sure that when you put the X table on a cart you use blocks to not bend the then very exposed spindle.
2. . When removing the gearbox in the knee it is *crucial* to first remove the guiding pin. This allows you to rotate the unit some 10 degrees clockwise to lift the crownwheel. You *will* break a teeth from the crownwheel otherwise !