Schaafmes Slijphouder: verschil tussen versies
| Regel 1: | Regel 1: | ||
| + | [[Categorie:Tool]][[Categorie:Metal]][[Categorie:Small]][[Categorie:Wood]]{{SafetyCat6}}{{NoiseCat3}} | ||
| + | |||
Speciale houder om messen te slijpen op de [[Vlakslijpmachine / Surface Grinder]]. | Speciale houder om messen te slijpen op de [[Vlakslijpmachine / Surface Grinder]]. | ||
[[Bestand:Knifejig-3.jpg|320px]][[Bestand:Knifejig-2.jpg|320px]][[Bestand:Knifejig-1.jpg|320px]] | [[Bestand:Knifejig-3.jpg|320px]][[Bestand:Knifejig-2.jpg|320px]][[Bestand:Knifejig-1.jpg|320px]] | ||
| − | Met dank aan HansB. Vraag | + | Met dank aan HansB. Vraag demo bij Hans of Dirk-Willem. Het is absoluut niet moeilijk. |
| + | |||
| + | # Mount jig on the [[Surface Grinder|Vlakslijpmachine / Surface Grinder]]; you typically will have to remove the magnetchuck. You need Spanner #22 for this. Check that the surfaces are clean - so that the jig is mounted parallel to the table. It will be diagonal. This is intentional. | ||
| + | # Ensure the jig is clean (so the knifes will seat well/flush) | ||
| + | # Ensure the knifes are clean (so the knifes will be tightly packet) | ||
| + | # Put the knifes in the jigs; hand tighten and then tighten the bolds gradually | ||
| + | # Puth the endstoppers as far left/right as you can; but where they still 'lock' in place. | ||
| + | # Lower the wheel over the knifes until you can just about no longer have a piece of (thin) paper in between. Err on the side of 'too high'. | ||
| + | # Gently check that it also does not touch at the far left/right | ||
| + | # Start the wheel. Move table forward so that the wheel is just 'before' the knifes. | ||
| + | # Start motion & coolant. | ||
| + | # Now gently lower the wheel until it just touches (usually at the far left or right side; the middle is often a bit lower. | ||
| + | # Make a full pass; then go down in steps of 5 or 10 until all nicks and scratches are gone. | ||
| + | # Step down 2; and do a 2 final passes (or 3 if it it still touches. | ||
| + | # Remove knifes & use the wetsteen(speksteen) to remove the bur on the back. | ||
Versie van 6 jan 2022 om 20:04
This equipment is safety category 6: Other equipment with no limits.
This equipment is Noise Category 3: Can be used at all hours. No limits.
Speciale houder om messen te slijpen op de Vlakslijpmachine / Surface Grinder.
Met dank aan HansB. Vraag demo bij Hans of Dirk-Willem. Het is absoluut niet moeilijk.
- Mount jig on the Vlakslijpmachine / Surface Grinder; you typically will have to remove the magnetchuck. You need Spanner #22 for this. Check that the surfaces are clean - so that the jig is mounted parallel to the table. It will be diagonal. This is intentional.
- Ensure the jig is clean (so the knifes will seat well/flush)
- Ensure the knifes are clean (so the knifes will be tightly packet)
- Put the knifes in the jigs; hand tighten and then tighten the bolds gradually
- Puth the endstoppers as far left/right as you can; but where they still 'lock' in place.
- Lower the wheel over the knifes until you can just about no longer have a piece of (thin) paper in between. Err on the side of 'too high'.
- Gently check that it also does not touch at the far left/right
- Start the wheel. Move table forward so that the wheel is just 'before' the knifes.
- Start motion & coolant.
- Now gently lower the wheel until it just touches (usually at the far left or right side; the middle is often a bit lower.
- Make a full pass; then go down in steps of 5 or 10 until all nicks and scratches are gone.
- Step down 2; and do a 2 final passes (or 3 if it it still touches.
- Remove knifes & use the wetsteen(speksteen) to remove the bur on the back.
