Schaafmes Slijphouder: verschil tussen versies
(→Instructions / use) |
|||
| Regel 14: | Regel 14: | ||
# Ensure the jig is clean (so the knifes will seat well/flush) | # Ensure the jig is clean (so the knifes will seat well/flush) | ||
# Ensure the knifes are clean (so the knifes will be tightly packet) | # Ensure the knifes are clean (so the knifes will be tightly packet) | ||
| − | # Put the knifes in the jigs; hand tighten and then tighten the bolds gradually | + | # Put the knifes in the jigs; hand tighten and then tighten the bolds gradually; in several stap. To avoid asymmetry/building up needless stress. |
| − | # Puth the endstoppers as far left/right as you can; but where they still 'lock' in place. | + | # Puth the endstoppers as far left/right as you can; but where they still easily 'lock' in place. |
# Lower the wheel over the knifes until you can just about no longer have a piece of (thin) paper in between. Err on the side of 'too high'. | # Lower the wheel over the knifes until you can just about no longer have a piece of (thin) paper in between. Err on the side of 'too high'. | ||
| − | # Gently check that it also does not touch at the far left/right | + | # Gently check that it also does not touch (at all) at the far left/right |
# Start the wheel. Move table forward so that the wheel is just 'before' the knifes. | # Start the wheel. Move table forward so that the wheel is just 'before' the knifes. | ||
# Start motion & coolant. | # Start motion & coolant. | ||
| − | # Now gently lower the wheel until it just touches (usually at the far left or right side; the middle is often a bit lower. | + | # Now gently lower the wheel in small steps until it just touches (usually at the far left or right side; the middle is often a bit lower. |
# Make a full pass; then go down in steps of 5 or 10 until all nicks and scratches are gone. | # Make a full pass; then go down in steps of 5 or 10 until all nicks and scratches are gone. | ||
| − | # Step down 2; and do a 2 final passes (or 3 if it it still touches. | + | # Best to use fairly small steps in the Y direction; and towards the high end for the X travel. You will see blueing if you dwell too much or try to take too much off. |
| − | # Remove knifes & use the wetsteen(speksteen) to remove the | + | # Step down (just) 2; and do a 2 final passes (or 3 if it it still touches somewhere) - i.e. letting it spark out. It may take a bit - as something seems quite heat/expansion sensitive. |
| + | # Remove knifes & use the wetsteen(speksteen) to remove the burs on the back. | ||
Versie van 17 jan 2022 om 22:05
This equipment is safety category 6: Other equipment with no limits.
This equipment is Noise Category 3: Can be used at all hours. No limits.
Speciale houder om messen te slijpen op de Vlakslijpmachine / Surface Grinder.
Met dank aan HansD. Vraag demo bij HansD of Dirk-Willem. Het is absoluut niet moeilijk.
Movie: https://vimeo.com/manage/videos/663078557 or https://vimeo.com/manage/videos/663078557
Instructions / use
- Mount jig on the Surface Grinder; you typically will have to remove the magnetchuck. You need Spanner #22 for this. Check that the surfaces are clean - so that the jig is mounted parallel to the table. It will be diagonal. This is intentional.
- Ensure the jig is clean (so the knifes will seat well/flush)
- Ensure the knifes are clean (so the knifes will be tightly packet)
- Put the knifes in the jigs; hand tighten and then tighten the bolds gradually; in several stap. To avoid asymmetry/building up needless stress.
- Puth the endstoppers as far left/right as you can; but where they still easily 'lock' in place.
- Lower the wheel over the knifes until you can just about no longer have a piece of (thin) paper in between. Err on the side of 'too high'.
- Gently check that it also does not touch (at all) at the far left/right
- Start the wheel. Move table forward so that the wheel is just 'before' the knifes.
- Start motion & coolant.
- Now gently lower the wheel in small steps until it just touches (usually at the far left or right side; the middle is often a bit lower.
- Make a full pass; then go down in steps of 5 or 10 until all nicks and scratches are gone.
- Best to use fairly small steps in the Y direction; and towards the high end for the X travel. You will see blueing if you dwell too much or try to take too much off.
- Step down (just) 2; and do a 2 final passes (or 3 if it it still touches somewhere) - i.e. letting it spark out. It may take a bit - as something seems quite heat/expansion sensitive.
- Remove knifes & use the wetsteen(speksteen) to remove the burs on the back.
