PowerNode White - Configuration: verschil tussen versies
(→Power setup / AC-DC and PoE Jumpers) |
(→External/separate current coil) |
||
| Regel 35: | Regel 35: | ||
The current coils can be on the PCB - but can also be replaced by a 3.5mm jacket and a standard pickup. | The current coils can be on the PCB - but can also be replaced by a 3.5mm jacket and a standard pickup. | ||
| − | * 3.5mm jackets: https://nl.aliexpress.com/item/1005004035360795.html [[Bestand:PCBjack-3_5mm.jpg| | + | * 3.5mm jackets: https://nl.aliexpress.com/item/1005004035360795.html [[Bestand:PCBjack-3_5mm.jpg|120px]] |
| − | * Current coil: https://nl.aliexpress.com/item/1005006003984501.html [[Bestand:Current-coil-3_5mm.jpg| | + | * Current coil: https://nl.aliexpress.com/item/1005006003984501.html [[Bestand:Current-coil-3_5mm.jpg|120px]] |
This is used on the [[Ceramic Oven]] its [[NodeCeramic]]. | This is used on the [[Ceramic Oven]] its [[NodeCeramic]]. | ||
Versie van 15 apr 2024 om 21:25
Inhoud
Jumpers
Power Jumpers
The relays can be switched 'as is'; where the NO/C/NO or NO/C of either relay is mapped to pin 1,2,3 for the first relay and to pin 4 and 5 for the second relay. Or they can be mapped to the N/L of the AC input on pin 6 and 7. Diagram:...
Power setup / AC-DC and PoE Jumpers
Power can come from several sources; US, PoE, an external source and an AC/DC transformer on the board.
There are 2 power sets - one for the electronics (typically 5V down to 3v3) and one for the relays and other externals (typically 5v, 12v or 24 volt).
For PoE - unless a variable 68k resister (potentiometer) is mounted and R?? is removed - the external voltage is set to 5V by this register. The resistor allows for 5v to around 40v (given the general the max of PoE on our switch).
The AC/DC transformer can be anything between 3v3 and 12volt. For higher voltages - beware that the 3v3 regulator needs to step it down for the electronics.
The jumps give the following options:
Hardware options
The boards allow for various extra `options'
Pushbutton and LED connectors
Normal two-pin XH 2.54 connector for the LED and for each of the push-buttons (inside the footprint). Same type as often used for fans on PCs.
Pushbuttons are 6x6mm standard pushbuttons; switch at least 10mm high. E.g. https://www.hobbyelectronica.nl/product/push-button-6x6x5/
External/separate current coil
The current coils can be on the PCB - but can also be replaced by a 3.5mm jacket and a standard pickup.
- 3.5mm jackets: https://nl.aliexpress.com/item/1005004035360795.html
- Current coil: https://nl.aliexpress.com/item/1005006003984501.html
This is used on the Ceramic Oven its NodeCeramic.
Pressure sensor
OLED screen
Used are Oled Display Module 12864 SH1106 I2C screens with 30 pins.
Enclosure
The PCB fits a 150x150 enclosure - such as zp150-150-60 series. E.g: https://www.tme.eu/nl/details/zp15015060jph-pc/behuizingen-universeel/kradex/zp150-150-60jph-tm-pc/ (around 10 euro).
Large 15 pin Connector
A large connector or socket can be used; 3.5mm pitch. E.g. https://de.aliexpress.com/item/1005006345862685.html - around one euro.
Extra IO connector
Normal 2.5mm pitch
Solid state relay
Two types of Solid State relays - in line and 'box'
