PowerNode White - Configuration: verschil tussen versies

Uit MakerSpace Leiden
Ga naar: navigatie, zoeken
(Nieuwe pagina aangemaakt met '= Jumpers = == Power Jumpers == The relays can be switched 'as is'; where the NO/C/NO or NO/C of either relay is mapped to pin 1,2,3 for the first relay and to p...')
 
(Pushbutton and LED connectors)
(6 tussenliggende versies door dezelfde gebruiker niet weergegeven)
Regel 1: Regel 1:
 +
[[Category:ACNode]][[Category:Infrastructuur]]
 +
 
= Jumpers =
 
= Jumpers =
  
Regel 6: Regel 8:
  
 
== Power setup / AC-DC and PoE Jumpers ==
 
== Power setup / AC-DC and PoE Jumpers ==
 +
 +
Power can come from several sources; US, PoE, an external source and an AC/DC transformer on the board.
 +
 +
There are 2 power sets - one for the electronics (typically 5V down to 3v3) and one for the relays and other externals (typically 5v, 12v or 24 volt).
 +
 +
For PoE - unless a variable 68k resister (potentiometer) is mounted and R?? is removed - the external voltage is set to 5V by this register. The resistor allows for 5v to around 40v (given the general the max of PoE on our switch).
 +
 +
The AC/DC transformer can be anything between 3v3 and 12volt. For higher voltages - beware that the 3v3 regulator needs to step it down  for the electronics.
 +
 +
The jumps give the following options:
  
 
= Hardware options =
 
= Hardware options =
Regel 15: Regel 27:
 
Normal two-pin XH 2.54 connector for the LED and for each of the push-buttons (inside the footprint). Same type as often used for fans on PCs.
 
Normal two-pin XH 2.54 connector for the LED and for each of the push-buttons (inside the footprint). Same type as often used for fans on PCs.
  
* See https://nl.aliexpress.com/item/1005006168591801.html [[Bestand:Xh254.jpg|50px]]
+
* See https://nl.aliexpress.com/item/1005006168591801.html [[Bestand:Xh254.jpg|120px]]
 +
 
 +
Pushbuttons are 6x6mm standard pushbuttons; switch at least 10mm high. E.g. https://www.hobbyelectronica.nl/product/push-button-6x6x5/ or https://www.tme.eu/nl/details/1301.9304/microschakelaars-tact/schurter/ -- around 50cent.
  
Pushbuttons are 6x6mm standard pushbuttons; switch at least 10mm high. E.g. https://www.hobbyelectronica.nl/product/push-button-6x6x5/
+
[[Bestand:Pushbutton-6x6mm.jpg|120px|miniatuur]]
  
 
== External/separate current coil ==
 
== External/separate current coil ==
Regel 23: Regel 37:
 
The current coils can be on the PCB - but can also be replaced by a 3.5mm jacket and a standard pickup.
 
The current coils can be on the PCB - but can also be replaced by a 3.5mm jacket and a standard pickup.
  
* 3.5mm jackets: https://nl.aliexpress.com/item/1005004035360795.html [[Bestand:PCBjack-3_5mm.jpg|30px]]
+
* 3.5mm jackets: https://nl.aliexpress.com/item/1005004035360795.html [[Bestand:PCBjack-3_5mm.jpg|120px]]
* Current coil: https://nl.aliexpress.com/item/1005006003984501.html [[Bestand:Current-coil-3_5mm.jpg|30px]]
+
* Current coil: https://nl.aliexpress.com/item/1005006003984501.html [[Bestand:Current-coil-3_5mm.jpg|120px]]
  
 
This is used on the [[Ceramic Oven]] its [[NodeCeramic]].
 
This is used on the [[Ceramic Oven]] its [[NodeCeramic]].
Regel 34: Regel 48:
 
Used are Oled Display Module 12864 SH1106 I2C screens with 30 pins.
 
Used are Oled Display Module 12864 SH1106 I2C screens with 30 pins.
  
[[Bestand:Screen-oled-30-i2c.jpg|50px]]
+
[[Bestand:Screen-oled-30-i2c.jpg|120px]]
  
 
== Enclosure ==
 
== Enclosure ==
Regel 41: Regel 55:
 
https://www.tme.eu/nl/details/zp15015060jph-pc/behuizingen-universeel/kradex/zp150-150-60jph-tm-pc/ (around 10 euro).
 
https://www.tme.eu/nl/details/zp15015060jph-pc/behuizingen-universeel/kradex/zp150-150-60jph-tm-pc/ (around 10 euro).
  
[[Bestand:150x150.jpg|150px]]
+
[[Bestand:150x150.jpg|120px]]
  
 
== Large 15 pin Connector ==
 
== Large 15 pin Connector ==
Regel 47: Regel 61:
 
A large connector or socket can be used; 3.5mm pitch. E.g. https://de.aliexpress.com/item/1005006345862685.html - around one euro.
 
A large connector or socket can be used; 3.5mm pitch. E.g. https://de.aliexpress.com/item/1005006345862685.html - around one euro.
  
[[Bestand:15pin-35mm.jpg|150]]
+
[[Bestand:15pin-35mm.jpg|120px]]
  
 
== Extra IO connector ==
 
== Extra IO connector ==

Versie van 15 apr 2024 om 21:28


Jumpers

Power Jumpers

The relays can be switched 'as is'; where the NO/C/NO or NO/C of either relay is mapped to pin 1,2,3 for the first relay and to pin 4 and 5 for the second relay. Or they can be mapped to the N/L of the AC input on pin 6 and 7. Diagram:...

Power setup / AC-DC and PoE Jumpers

Power can come from several sources; US, PoE, an external source and an AC/DC transformer on the board.

There are 2 power sets - one for the electronics (typically 5V down to 3v3) and one for the relays and other externals (typically 5v, 12v or 24 volt).

For PoE - unless a variable 68k resister (potentiometer) is mounted and R?? is removed - the external voltage is set to 5V by this register. The resistor allows for 5v to around 40v (given the general the max of PoE on our switch).

The AC/DC transformer can be anything between 3v3 and 12volt. For higher voltages - beware that the 3v3 regulator needs to step it down for the electronics.

The jumps give the following options:

Hardware options

The boards allow for various extra `options'

Pushbutton and LED connectors

Normal two-pin XH 2.54 connector for the LED and for each of the push-buttons (inside the footprint). Same type as often used for fans on PCs.

Pushbuttons are 6x6mm standard pushbuttons; switch at least 10mm high. E.g. https://www.hobbyelectronica.nl/product/push-button-6x6x5/ or https://www.tme.eu/nl/details/1301.9304/microschakelaars-tact/schurter/ -- around 50cent.

Pushbutton-6x6mm.jpg

External/separate current coil

The current coils can be on the PCB - but can also be replaced by a 3.5mm jacket and a standard pickup.

This is used on the Ceramic Oven its NodeCeramic.

Pressure sensor

OLED screen

Used are Oled Display Module 12864 SH1106 I2C screens with 30 pins.

Screen-oled-30-i2c.jpg

Enclosure

The PCB fits a 150x150 enclosure - such as zp150-150-60 series. E.g: https://www.tme.eu/nl/details/zp15015060jph-pc/behuizingen-universeel/kradex/zp150-150-60jph-tm-pc/ (around 10 euro).

150x150.jpg

Large 15 pin Connector

A large connector or socket can be used; 3.5mm pitch. E.g. https://de.aliexpress.com/item/1005006345862685.html - around one euro.

15pin-35mm.jpg

Extra IO connector

Normal 2.5mm pitch

Solid state relay

Two types of Solid State relays - in line and 'box'

SSRelay-1.jpgSSRelay-2.jpg