MT2: verschil tussen versies
| (20 tussenliggende versies door 3 gebruikers niet weergegeven) | |||
| Regel 1: | Regel 1: | ||
| − | We have various MT2 (Morse Taper 2) holders and machines. | + | [[Category:Tools]][[Category:Metal working tools]][[Category:Metal lathe and mill tools]][[Category:Wood working tools]] |
| + | {{SafetyCat6}}{{NoiseCat3}} | ||
| + | |||
| + | We have various MT2 ([https://en.wikipedia.org/wiki/Machine_taper Morse Taper 2]) holders and machines. (For MT4 equipment to go in the lathe spindle, see [[MT4]]) | ||
| + | |||
| + | |||
| + | [[Bestand:MT2TaperTooling01.jpg|thumb|MT2 tooling setup next to the lathe]] | ||
| + | [[Bestand:MT2ER25Collet01.jpg|thumb|MT2 ER25 Collet Holder]] | ||
| + | [[Bestand:MT2-MT4-01.jpg|thumb|MT2 to MT4 adapter to allow putting MT2 items to fit in the lathe chuck spindle]] | ||
| + | |||
Such as: | Such as: | ||
| − | * [[Pijp-center Tail - Stock Pipe Center]] | + | * [[Pijp-center Tail - Stock Pipe Center]] voor dikke pijpen |
| − | * [[MT2 Hand chuck]] | + | * Diverse [[MT2 Hand chuck]] |
* [[ER 25/32/40 Collets and holders]] met MT2 einde. | * [[ER 25/32/40 Collets and holders]] met MT2 einde. | ||
| − | * Diverse houders en adaptors om dingen onder een hoek vast te houden. | + | * Diverse houders en adaptors om dingen onder een hoek vast te houden. (Where are they?) |
| − | * | + | * Live centre |
| − | * Tap houders. | + | * Dead centre |
| + | * Tap houders. (Where are these stored?} | ||
| + | * 22mm drill | ||
And these can be used on several machines: | And these can be used on several machines: | ||
| − | * [Abene | + | * [[Abene Metal Mill / Freesbank]] |
| − | * [[Houtdraaibank]] | + | * [[Wood Lathe / Houtdraaibank]] |
| − | * [[ | + | * [[Metal Lathe / Metaal draaibank]] |
| − | * [[Drill | + | * [[Drill Press Metal / Kolomboor metaal]] |
| + | * [[Drill Press Wood / Boorkolom hout]] | ||
| + | |||
| + | Useful too: | ||
| + | |||
| + | * [[MT2/MT4|MT2/MT4 convertor]] | ||
Huidige versie van 16 nov 2024 om 23:04
This equipment is safety category 6: Other equipment with no limits.
This equipment is Noise Category 3: Can be used at all hours. No limits.
We have various MT2 (Morse Taper 2) holders and machines. (For MT4 equipment to go in the lathe spindle, see MT4)
Such as:
- Pijp-center Tail - Stock Pipe Center voor dikke pijpen
- Diverse MT2 Hand chuck
- ER 25/32/40 Collets and holders met MT2 einde.
- Diverse houders en adaptors om dingen onder een hoek vast te houden. (Where are they?)
- Live centre
- Dead centre
- Tap houders. (Where are these stored?}
- 22mm drill
And these can be used on several machines:
- Abene Metal Mill / Freesbank
- Wood Lathe / Houtdraaibank
- Metal Lathe / Metaal draaibank
- Drill Press Metal / Kolomboor metaal
- Drill Press Wood / Boorkolom hout
Useful too:
