Aambeeld en smeedgereedschap: verschil tussen versies
(→Tools) |
|||
| Regel 14: | Regel 14: | ||
Owner: Makerspace Leiden | Owner: Makerspace Leiden | ||
| + | |||
| + | |||
For fine detail work, or for where you want the work piece closer to you. Also useful that the edges of this are sharper than the main anvil, this can be useful for dividing work. | For fine detail work, or for where you want the work piece closer to you. Also useful that the edges of this are sharper than the main anvil, this can be useful for dividing work. | ||
| Regel 21: | Regel 23: | ||
Owner: Makerspace Leiden | Owner: Makerspace Leiden | ||
| + | |||
Used to cut the work from a longer piece of stock. Try to avoid hitting the cutting edge with the hammer. Cut most of the way through, then bend the work to fatigue it from the stock. | Used to cut the work from a longer piece of stock. Try to avoid hitting the cutting edge with the hammer. Cut most of the way through, then bend the work to fatigue it from the stock. | ||
| Regel 30: | Regel 33: | ||
Owner: Makerspace Leiden | Owner: Makerspace Leiden | ||
| + | |||
This is a useful tool for bending long pieces. It's a bit too big to fit the hardy hole currently, just needs a few minutes with a grinder to make it fit better. | This is a useful tool for bending long pieces. It's a bit too big to fit the hardy hole currently, just needs a few minutes with a grinder to make it fit better. | ||
| Regel 42: | Regel 46: | ||
Owner: Makerspace Leiden | Owner: Makerspace Leiden | ||
| + | |||
| + | |||
[[Bestand:Tongs-01.jpg|800px|Tongs with round end.]] | [[Bestand:Tongs-01.jpg|800px|Tongs with round end.]] | ||
| Regel 52: | Regel 58: | ||
Owner: Makerspace Leiden | Owner: Makerspace Leiden | ||
| + | |||
High temperature IR thermometer that can measure upto 1600C. Useful for checking the forge temp, both during use, and to make sure it's cooled down so you don't burn yourself. Do not store with the battery installed. | High temperature IR thermometer that can measure upto 1600C. Useful for checking the forge temp, both during use, and to make sure it's cooled down so you don't burn yourself. Do not store with the battery installed. | ||
Versie van 25 jan 2025 om 17:57
Intro
MSL Leiden has a variety of blacksmithing tools available for it's members. Some tools are on loan (from Jochem and Leon). Others are owned by the space. This page details what tools we have available to us.
Tools
Hardy Small Anvil
Owner: Makerspace Leiden
For fine detail work, or for where you want the work piece closer to you. Also useful that the edges of this are sharper than the main anvil, this can be useful for dividing work.
Hardy hole cut off tool
Owner: Makerspace Leiden
Used to cut the work from a longer piece of stock. Try to avoid hitting the cutting edge with the hammer. Cut most of the way through, then bend the work to fatigue it from the stock.
Bending Forke
Owner: Makerspace Leiden
This is a useful tool for bending long pieces. It's a bit too big to fit the hardy hole currently, just needs a few minutes with a grinder to make it fit better.
Hammers
Round nose tongs - 500mm - 16mm Dia
Owner: Makerspace Leiden
Misc
IR Thermometer
Owner: Makerspace Leiden
High temperature IR thermometer that can measure upto 1600C. Useful for checking the forge temp, both during use, and to make sure it's cooled down so you don't burn yourself. Do not store with the battery installed.
Farriers' Brush
Owner: Makerspace Leiden
Large steel bristled stiff farriers brush. used to brush the scale off a work piece while it's hot. The design shields the hand from the heat.
