Transfer Punch Overbreng stempel: verschil tussen versies
(Nieuwe pagina aangemaakt met 'Categorie:ToolCategorie:MetalCategorie:SmallCategorie:Wood {{SafetyCat6}} {{NoiseCat3}} We have two sets of transfer punches. One metric, one imper...') |
|||
(14 tussenliggende versies door 2 gebruikers niet weergegeven) | |||
Regel 1: | Regel 1: | ||
− | [[Categorie:Tool]][[Categorie:Metal]][[Categorie:Small]][[Categorie:Wood]] | + | [[Categorie:Tool]][[Categorie:Metal]][[Categorie:Small]][[Categorie:Wood]][[Categorie:Imperial]] |
− | |||
− | |||
− | We have two sets of transfer punches. One metric, one imperial. | + | We have two sets of transfer punches. One metric, one imperial (try not to mix them). |
− | [[Bestand:transverpunch.jpeg| | + | [[Bestand:transverpunch.jpeg|300px|Transferpunch]][[Bestand:transverpunch-closeup.jpeg|399px|Closeup tranferpunch]] |
− | [[Bestand:transverpunch-closeup.jpeg| | ||
− | There are to (very accurately) transfer a hole to a plate/object under that hole. | + | There are to (very accurately) transfer a hole to a plate/object under that hole. |
See youtube or https://www.table-saw-guide.com/transfer-punch.html for an example. | See youtube or https://www.table-saw-guide.com/transfer-punch.html for an example. | ||
Regel 14: | Regel 11: | ||
Kept in the metal workshop - but also very useful if you are working with hard wood. | Kept in the metal workshop - but also very useful if you are working with hard wood. | ||
− | {{ | + | == History == |
+ | |||
+ | 2020/6/13 - Metric 5.5mm gone missing | ||
+ | |||
+ | == Location == | ||
+ | |||
+ | Metal workshop, near the [[Drill press / boorkolom]]. | ||
+ | |||
+ | == Ownership == | ||
+ | |||
+ | Bought by the space - sometime 2017. | ||
+ | |||
+ | |||
+ | {{Fragiel}} | ||
+ | {{SafetyCat6}} | ||
+ | {{NoiseCat3}} | ||
+ | {{Imperial}} |
Versie van 13 jun 2020 om 13:52
We have two sets of transfer punches. One metric, one imperial (try not to mix them).
There are to (very accurately) transfer a hole to a plate/object under that hole.
See youtube or https://www.table-saw-guide.com/transfer-punch.html for an example.
Kept in the metal workshop - but also very useful if you are working with hard wood.
History
2020/6/13 - Metric 5.5mm gone missing
Location
Metal workshop, near the Drill press / boorkolom.
Ownership
Bought by the space - sometime 2017.
Handle with care.
This is a precision tool with exact dimensions and straightness.
That means: handle it gently, don't hammer on it or use it as a crowbar and so on.
(if you need a crowbar - these are wonderful for that!)
It is very important that if you accidentally drop it or think it may be out of line
- either mark the tool very clearly...
- or report this to the mailing list...
...so that your fellow makers do not ruin their work.
This equipment is safety category 6: Other equipment with no limits.
This equipment is Noise Category 3: Can be used at all hours. No limits.
WARNING: Imperial tools have slightly different sizes than Metric ones.
Using the wrong one will often damage the bolt, nut or whatever you are working on. See this list for all the imperial tools we have.
Try not to mix them with our metric tools -- to make sure your fellow maker does not ruin their work.
Be especially careful with the close friends, such as sizes like 5/8inch and 16mm;
although the difference is 0.13mm - you will ruin (or usually just crack) a collet or similar..