DRO maten en manual: verschil tussen versies
| (7 tussenliggende versies door dezelfde gebruiker niet weergegeven) | |||
| Regel 1: | Regel 1: | ||
| − | [[Category:Metal]] | + | [[Category:Tools]][[Category:Metal working tools]][[Category:Metal lathe and mill tools]][[Category:Measuring tools]] |
| − | [[ | + | {{Fragiel}} |
== Draaibank / Lathe : DR_2L (LED) == | == Draaibank / Lathe : DR_2L (LED) == | ||
| − | Digitale Readout (2 Linealen) op de [[ | + | Digitale Readout (2 Linealen) op de [[Metal Lathe / Metaal draaibank| Draaibank voor metaal]]. |
[[Bestand:Dro-lathe-unit.jpg|200px|DRL Lathe DR_2L (LED)]] | [[Bestand:Dro-lathe-unit.jpg|200px|DRL Lathe DR_2L (LED)]] | ||
| Regel 11: | Regel 11: | ||
== Staande Frees / Abene: DLS-3V (LCD) == | == Staande Frees / Abene: DLS-3V (LCD) == | ||
| − | 3 assen, XYZ, digitale readout (digitale linealen) voor op de [[Abene | + | 3 assen, XYZ, digitale readout (digitale linealen) voor op de [[Abene Metal Mill / Freesbank]]. |
[[Bestand:Dro-abene-unit.jpg|200px|DRO Abene DLS-3V (LCD)]] | [[Bestand:Dro-abene-unit.jpg|200px|DRO Abene DLS-3V (LCD)]] | ||
Huidige versie van 11 nov 2024 om 23:13
Handle with care.
This is a precision tool with exact dimensions and straightness.
That means: handle it gently, don't hammer on it or use it as a crowbar and so on.
(if you need a crowbar - these are wonderful for that!)
It is very important that if you accidentally drop it or think it may be out of line
- either mark the tool very clearly...
- or report this to the mailing list...
...so that your fellow makers do not ruin their work.
Inhoud
Draaibank / Lathe : DR_2L (LED)
Digitale Readout (2 Linealen) op de Draaibank voor metaal.
Handleiding: [Delos DR_2L].
Staande Frees / Abene: DLS-3V (LCD)
3 assen, XYZ, digitale readout (digitale linealen) voor op de Abene Metal Mill / Freesbank.
Handleiding: [Delos DLS-3V].
History
Purchase
Bought by the space summer 2020.
Abene mill display replacement
Over the 2023/2024 winter holidays, the LCD display in the Abene DRO (the DLS-3V) failed. User:PeterBosch confirmed that it was due to the flex PCB starting to separate from the panel's Chip-On-Glass style controller. This type of failure is not repairable, and as such the entire panel needed to be replaced.
The replacement panel was bought from this AliExpress listing (careful - the default option is "only touch" - which means only a digitizer fitting the module, and we need "only lcd" - the LCD itself).
After installing the new panel, the DRO appears to be fully functional again.
Electronics
Linealen
- Abene:
* X: 750mm – DLS-W-750 mm * Y: 500mm – DLS-W-500 mm * Z: 200mm – DLS-W-250 mm
- Lathe
* X: 760mm: DLS-W-800 mm * Y: 160mm: DLS-S-200 mm compacte liniaal
