Oscillating Bobbin Sander: verschil tussen versies
(→Tasks prior to clearing the machine for full use =) |
k (MarkKlaauw heeft de pagina OscillatingBobbinSander hernoemd naar Oscillating Bobbin Sander zonder een doorverwijzing achter te laten) |
||
(8 tussenliggende versies door 5 gebruikers niet weergegeven) | |||
Regel 1: | Regel 1: | ||
− | [[Category:Wood]][[Category:SafetySheet]][[Category:Tool]][[ | + | [[Category:Wood]][[Category:SafetySheet]][[Category:Tool]] |
+ | [[Categorie:Tools]][[Categorie:Wood working tools]] | ||
+ | {{SafetyCat3}}{{NoiseCat2}}{{DustControl2}} | ||
+ | |||
+ | {{SafetyCat3}}{{NoiseCat2}}{{DustControl2}} | ||
[[Bestand:ocbobbsander.jpg|300px|thumb|left]] | [[Bestand:ocbobbsander.jpg|300px|thumb|left]] | ||
Regel 24: | Regel 28: | ||
== Main rules and instructions == | == Main rules and instructions == | ||
− | ''Opmerking vooraf:'' Het veilig gebruiken van een | + | ''Opmerking vooraf:'' Het veilig gebruiken van een oscillerende schuurmachine leer je niet door het lezen van de wiki en de handleidingen; maar door goede praktijkinstructie en oefening op de machine. Vraag dus om hulp en instructie wanneer nodig. |
# Use hearing protection, (safety)glasses and safe clothing. | # Use hearing protection, (safety)glasses and safe clothing. | ||
Regel 87: | Regel 91: | ||
# Make sure the belt is all the way down; rotate it a bit until it 'clicks' in place. You should almost see the axis flush with the top. [[Bestand:Osc-pin-belt-mounted.jpg|60px]] | # Make sure the belt is all the way down; rotate it a bit until it 'clicks' in place. You should almost see the axis flush with the top. [[Bestand:Osc-pin-belt-mounted.jpg|60px]] | ||
# Then mount the washer and tightening knob [[Bestand:Osc-pin-belt-flush.jpg|60px]] | # Then mount the washer and tightening knob [[Bestand:Osc-pin-belt-flush.jpg|60px]] | ||
+ | |||
+ | == Supplies == | ||
+ | |||
+ | Gekocht 2019-1-17: | ||
+ | |||
+ | # HBM 6 Delige Schuurdrumset Korrel 80 voor Oscillerende schuurmachine Artikelnummer: 2160 | EAN: 7435125185173 | ||
+ | # HBM 6 Delige Schuurdrumset Korrel 120 voor Oscillerende schuurmachine Artikelnummer: 2161 | EAN: 7435125185180 | ||
+ | # HBM 6 Delige Schuurdrumset Korrel 240 voor Oscillerende schuurmachine Artikelnummer: 2162 | EAN: 7435125185197 | ||
+ | |||
+ | == Stof Afvoerbuis == | ||
+ | |||
+ | Volgens de documentatie: ''The dust exhaust port has an internal diameter of 36 mm and an outside diameter of 39 mm.'' |
Huidige versie van 29 jul 2024 om 20:17
This equipment is safety category 3:
- Mandatory, in person, instructions.
- Make sure you read the Wiki before asking.
This equipment is Noise Category 2:
Can be used at all hours, but in moderation.
Be considerate; if you feel you need to wear ear protection,
then only use the tool between 07:00 and 19:00.
This equipment is should be used with active dust control.
Connect the shopvac prior to use.
This equipment is safety category 3:
- Mandatory, in person, instructions.
- Make sure you read the Wiki before asking.
This equipment is Noise Category 2:
Can be used at all hours, but in moderation.
Be considerate; if you feel you need to wear ear protection,
then only use the tool between 07:00 and 19:00.
This equipment is should be used with active dust control.
Connect the shopvac prior to use.
Documentation:
- https://www.youtube.com/watch?v=1RYAR111Zg8
- https://github.com/MakerSpaceLeiden/Manuals/raw/master/Houtbewerking/oscillatingsander.pdf
Inhoud
Algemeen
The bobbin sander is suitable for most types of woods as wel as other material such as (hard, thermo-harding) plastic glass -- provided that it does not `gum up' the bobbin. As it is to be primarily used for wood - contamination or use with metal is out. (If you do need it for metal; take it to the metal shop and clean the machine extensively afterwards to avoid ruining the next woodmakers work).
This equipment is safety category 4:
- In-person, instructions strongly advised but not mandatory.
- Reading, and following, the instructions on the Wiki is mandatory!
This equipment is Noise Category 2:
Can be used at all hours, but in moderation.
Be considerate; if you feel you need to wear ear protection,
then only use the tool between 07:00 and 19:00.
Opstelling
Make sure that the area around you is clear; and that nothing (including your clothing, hairs or jewelery) an be caught in the rotating parts. Be sure to connect the dust-exaction and either switch it on all the time (manual) or put it on `auto'.
Main rules and instructions
Opmerking vooraf: Het veilig gebruiken van een oscillerende schuurmachine leer je niet door het lezen van de wiki en de handleidingen; maar door goede praktijkinstructie en oefening op de machine. Vraag dus om hulp en instructie wanneer nodig.
- Use hearing protection, (safety)glasses and safe clothing.
- Leave the machine clean. If it is found not clean; clean it first; or do not use it. The last person to use it is responsible for leaving it fully and completely cleaned.
- Don't leave it running unattended.
- It is mandatory to report issues, malfunctions, lack of supplies to the mailing list.
Prior to use
- Verify that the machine is clean and looks ok.
- Make sure it is wired up; and connected to the dust extraction.
- Make sure the space around it is free/clean.
- Switch the machine shortly on - to check it runs smoothly; without vibration and that the dust extraction comes on.
- Check that the sand-paper is not slipping.
- Check your material for things like old nails.
- Keep listening to the sound of the machine; it should be regular without whining or high pitches.
In case of doubt - check the manual or ASK.
Wat betreft de machine schoon en veilig achterlaten - per algemene makerspace regel is dit altijd de verantwoordelijkheid van de *laatste* gebruiker. Dus als je de troep van een ander niet wil opruimen; meld het dan - en gebruik de machine niet. Zodra je iets gebruikt ben je verantwoordelijk voor het in goede en schone staat achterlaten van de machine; en het melden van storingen of defecten.
Dangers
- Hair, loose clothing or similar getting caught and sucked in.
- Bits of machinery coming loose and flying around
- Dust and splinters in hands & eyes.
- Very high temperatures due to rubbing (rather than sanding) and smoldering wood.
Instruction
Instruction is optional - do check the video - or ask on the mailing list if you want someone to show you. This generally takes 10-15 minutes.
Issues and defects to be reported to: deelnemers@makerspaceleiden.nl within 24 hours.
Accidents (i.e. that require first aid or fire extinguishers) are to be reported at bestuur@makerspaceleiden.nl immediately.
Use
See the manual at: https://github.com/MakerSpaceLeiden/Manuals/raw/master/Houtbewerking/oscillatingsander.pdf for full instructions; or the short primer below.
There are two ways to use the machine; with a round bobbin or with a short sanding belt. The first is useful for narrow corners; the latter for edges.
Using the bobbin
- Put the yellow plate (1) in the machine;
- select a spacer (2) that is a bit larger than the bobbin (3) you are to use. And slide this over the pin.
- then slide the bobbin (3) over the pin.
- pick the largest washer (4) that still fits.
- Then use the knob to tighten it all; the rubber should expand a little to 'grab' the sanding paper.
When selecting the spacer (2) - be sure that there is space around the bobbin; as it will start moving up&down.
Using the sander
- Find the belt, tightening knob and the silver coloured washer.
- Mount the sanding belt - checking that the pin on the non-axle side slides into the plastic washer.
- Make sure the belt is all the way down; rotate it a bit until it 'clicks' in place. You should almost see the axis flush with the top.
- Then mount the washer and tightening knob
Supplies
Gekocht 2019-1-17:
- HBM 6 Delige Schuurdrumset Korrel 80 voor Oscillerende schuurmachine Artikelnummer: 2160 | EAN: 7435125185173
- HBM 6 Delige Schuurdrumset Korrel 120 voor Oscillerende schuurmachine Artikelnummer: 2161 | EAN: 7435125185180
- HBM 6 Delige Schuurdrumset Korrel 240 voor Oscillerende schuurmachine Artikelnummer: 2162 | EAN: 7435125185197
Stof Afvoerbuis
Volgens de documentatie: The dust exhaust port has an internal diameter of 36 mm and an outside diameter of 39 mm.