Node Chips

Node for paying Crisps (Chips). Onderdeel van het Space tegoed betalings systeem.

Location

Physical: Kitchen. 192.168.6.49 on the Internet.

What does it do?

The display normally displays a static price. The price is for one packet of crips.

Swipe your door tag just once pay for packet.

Hardware vervangen/repareren

See Payment Terminal with 4 seven segment displays. Current incarnation:

• Wifi-Mac address: 3C:71:BF:D0:6A:08
• Software version 1.08
• Uses Green PCB that has been butchered a fair bit.
• Normal 220v AC/DC 5 volt power supply (0.2 Watt)
• Top dot of the 7-segment display has been painted black
• Boards are floating a bit / rattling in the box.

Network details

Telnet to 192.168.6.49 for details.

ac/log/4x7-1-08-d06a08 Crispy Crisps, Crokante Chips 

{
  "rfid_scans": 0,
  "rfid_misses": 0,
  "ota": true,
  "state": 3,
  "IP_address": "192.168.6.49",
  "Mac_address": "3C:71:BF:D0:6A:08",
  "Paid": 0.00,
  "PaidSeconds": 0,
  "Version": "F1-08",
  "Firmware": "4x7-1-08-d06a08",
  "heap": 187000,
  "coreTemp": 53.3,
  "loopRate": 20.0
}

Display messages

1. During startup
   1. F X-YY - version number firmware during booting.
   2. CONN - connecting to WiFi
   3. NTP - getting the time
   4. F CA - Fetching the Certificate Authority
   5. F PL - Fetching the price list
   6. FAIL - failed to connect to WiFi; will reboot.
   7. any error message - scrolling error message & after which either reboot or hang if it unrecoverable.
2. At the end of startup (from this point onwards OTA is possible).
   1. ---- - fully started up; but have not yet gotten the pricelist
   2. no prices - price list could not be fetched. Will retry for a few minutes every 15 seconds; then reboot.
3. In normal payment mode
   1. X.YY - price to pay when you swipe. There is no leading zero.
   2. [--] - in the process of paying
   3. FAIL - payment failed
   4. paid - you have paid
   5. MM:SS -- a minute and second countdown. Once at zero - the heating switches off. There is always a leading zero.
   6. any error message - scrolling error message.
      1. FAIL -1 - netwerk/wifi error. Powercyle de unit.
      2. FAIL -4 - netwerk/wifi error. Powercyle de unit.
      3. FAIL 40X Gebruik je een geldige tag ?
      4. FAIL 500 Error op de server; mail noc@.
4. During Over the Air reprogramming.
   1. PROG - start of OTA update
   2. F XX - OTA; uploading new firmware; XX is the percentage fetched
   3. DONE - successful end of OTA. Unit will reboot.
   4. any error message - scrolling error message & after which the device will switch back to the old/current firmware
      1. FO:AF - OTA authentication failed
      2. FO:BF - OTA begin failed
      3. FO:CF - OTA connect failed
      4. FO:RF - OTA receive failed
      5. FO:EF - OTA end failed
      6. FO:OF - OTA 'other' failure
5. During initial pairing / post an OTA
   1. REG Registering with the server
   2. PAIR requesting to pair; swipe an admin tag.
   3. Er::PL failed to get a pricelist - typically as it has not been associated with a station/pricelist in the CRM yet.
   4. any error message - scrolling error message.

Code is at https://github.com/MakerspaceLeiden/makerspaceleiden-payment-node-7segments.