Vandiktebank: verschil tussen versies

Uit MakerSpace Leiden
Ga naar: navigatie, zoeken
(Safety)
Regel 4: Regel 4:
  
  
This equipment is safety category 1 - the most dangerous class of machines.<br />Mandatory instruction is required.<br />The ''[liability waiver]'' needs to be on file and approval from the trustees is required (post instruction).<br />Two people present at all times.<br />Can only be used between 07:00 and 19:00 because of noise.
+
This equipment is safety category 1 - the most dangerous class of machines.<br />Mandatory instruction is required.<br />The ''[liability waiver]'' needs to be on file and approval from the trustees is required (post instruction).<br />Two people present at all times.<br />Can only be used between 07:00 and 19:00 because of noise.
  
 +
<br  /><br  />{{NoiseCat1}}{{DustControl1}}
  
This equipment is safety category 1 - the most dangerous class of machines.<br />Mandatory instruction is required.<br />The ''[liability waiver]'' needs to be on file and approval from the trustees is required (post instruction).<br />Two people present at all times.<br />Can only be used between 07:00 and 19:00 because of noise.
 
  
 
 
 
<br /><br />{{NoiseCat1}}{{DustControl1}}
 
  
  

Versie van 5 mei 2020 om 20:50

Safety

This equipment is safety category 1 - the most dangerous class of machines.


Mandatory instruction is required.


The [liability waiver] needs to be on file and approval from the trustees is required (post instruction).
Two people present at all times.
Can only be used between 07:00 and 19:00 because of noise.


This equipment is safety category 1 - the most dangerous class of machines.
Mandatory instruction is required.
The [liability waiver] needs to be on file and approval from the trustees is required (post instruction).
Two people present at all times.
Can only be used between 07:00 and 19:00 because of noise.



This equipment is Noise Category 1: can only be used between 07:00 and 19:00.
Wear hearing protection.

This equipment MUST be used with active dust control:

  • Connect a shop-vac prior to use and keep it on while using it.
  • Let it run for 10-20 seconds post use.


Not doing so endangers the operator, others, the space and the equipment.


Regarding the DeWalt Dust Extractor:

  • Do not fill the bag past 2/3rd of its capacity.
  • Check for enough airflow before using the connected tool.
  • Check that there is no (hot/smoldering) wood in the bottom of the machine when you smell something.








Vandiktebank.jpg


SafetyVandiktebank.png

Intro

  • ALWAYS connect the dust/chip extractor before starting the machine (GroteStofAfzuiger)! . Otherwise chips clog up the head and may start a fire!
  • Make sure your wood has absolutely no metal in it (screws, nails, staples). It's a small effort vs. re-sharpening and re-setting three knives
  • Make sure your wood is clean/dry. If it leaks sap, or leaves any other markings, please clean the bed and rollers with a solvent, and then re-oil with leibaanolie (from the metal cabinet)
  • You can check the height of the rollers by lowering the bed and putting a metal ruler on its edge over the roller/bed. You can adjust the height of the rollers, and hence the amount of snipe, by adjusting the black knob on the front right of the bed
  • Once the machine is stopped, open the head and clear the chips from the mechanism

Messen rond de 350x30x3mm - [en 350x35x3] zijn een handelsmaat. Ze kosten rond de 20 euro per stuk.

Slijpen kost rond de 8 euro per mes bij [Slijperij Vlijm] op de Flevoweg (achter de Gamma).

Access control

VandiktenodeOutside.jpeg

This node is under NodeVanDikteBank control. Swipe your badge; then press the green button on the safety contactor to turn it on.

Press the red button on the safety contactor to turn it off.

Na gebruik

  1. Machine geod schoonmaken; ook van binnen. De kap kan je optillen zodat je overal goed bij kan.
  2. Check dat de zak van de GroteStofAfzuiger niet meer dan half vol is - indien wel - leeg deze dan (zie instructies]).

Wat te doen als ik een mes kapot maak

Dat is niet erg - en kan bij normaal gebruik gebeuren. Meld het in elk geval meteen op de deelnemerslijst. Zodat de volgende persoon zijn hout niet ruinieerd.

Als het komt doordat je een spijker geraakt hebt, of als je een veelgebruiker bent, of met erg hard hout werkt - dan mag je schuldgevoel natuurlijk afkopen door de messen te laten slijpen, door nieuwe te doneren of door 15-25 euro in de pot te stoppen.

Incident report

Date Who Issue
2018-07-13 Dirk-Willem van Gulik Machine taken out of use; see https://mailman.makerspaceleiden.nl/mailman/private/deelnemers/2018-July/017273.html
2018-08-01 Henk Delsink Machine back in use; repaired; see https://mailman.makerspaceleiden.nl/mailman/private/deelnemers/2018-August/017404.html

Maintenance

Re-calibrating the rollers

Integrated in the bed are two rollers that help feed the material through the planer. For each rollers there is a a-centric adjustment ring which you can use to level the rollers parallel to the bed. Loosen the integrated bolt with a 4mm hex driver, place the bed on its side for easier access to the a-centric rings. Take a ruler and place it on top of the roller, on the bed side where the roller adjustment knob is located. This will be the reference side for our adjustments. Lower the rollers until the ruler is barely touching, now check the opposite side. Adjust the a-centric ring needed to raise or lower the roller. Repeat for the second roller. When done don't forget to fix the integrated bolt.

History

Datum Wie Wat
2/9/2018 Ramon Messen meegenomen om te slijpen.
21/10/2018 DirkWillem Nieuwe messen besteld.
2018-10-23 Dirk-Willem van Gulik Set van 3 reserve messen via vriend Ramon terug op space. Naar Vlijm gebracht.
2018-10-25 Dirk-Willem van Gulik Nieuwe messen op space neergelegd. HansD zal ze er in zetten.
2018-10-25 Dirk-Willem van Gulik Set van 2x3 nieuwe messen complate. Op space.
2020-01-24 Alex Yanson Cleaned and re-oiled the bed and the rollers, tightened loose screws.
2020-05-03 Jelle Grunstra Reattached the roller bar, fixed bolt with Locktite. Re-callibrated the rollers, added description to the Wiki