Ultimaker 2: verschil tussen versies
Regel 59: | Regel 59: | ||
See also: <br/> | See also: <br/> | ||
− | [https://www.youtube.com/watch?v=M2-pHgJQaI4 Automic Cleanout (Youtube)] <Br/> | + | * [https://www.youtube.com/watch?v=M2-pHgJQaI4 Automic Cleanout (Youtube)] <Br/> |
− | [https://support.3dverkstan.se/article/10-the Automic Cleanout manual] | + | * [https://support.3dverkstan.se/article/10-the Automic Cleanout manual] |
=== Manual and procedures === | === Manual and procedures === | ||
For supplier manuals see: <Br/> | For supplier manuals see: <Br/> | ||
− | [https://support.ultimaker.com/hc/en-us/sections/360003504360 Ultimaker Documentation] <Br/> | + | * [https://support.ultimaker.com/hc/en-us/sections/360003504360 Ultimaker Documentation] <Br/> |
− | [https://support.ultimaker.com/hc/en-us/articles/360011811480-The-Ultimaker-2-user-manuals Ultimaker Manuals] | + | * [https://support.ultimaker.com/hc/en-us/articles/360011811480-The-Ultimaker-2-user-manuals Ultimaker Manuals] |
==== Settings ==== | ==== Settings ==== |
Versie van 3 jun 2020 om 20:08
This equipment is safety category 3:
- Mandatory, in person, instructions.
- Make sure you read the Wiki before asking.
This equipment is Noise Category 3: Can be used at all hours. No limits.
Inhoud
Ultimaker printers
The Makerspace has two 3D printers:
- Ultimaker 2 +
- Ultimaker 2 Extended +
Characteristics of the printers
Property | Ultimaker 2+ | Ultimaker 2 Extended + |
---|---|---|
Max. size [mm] | 223x223x205 | 223x223x305 |
Nozzle size | 0.25, 0.4, 0.6, 0.8 | 0.25, 0.4, 0.6, 0.8 |
- | - | - |
Maintenance
See Maintenance Ultimaker 2+ for detailed descriptions on maintenance.
Recommended maintenance schedule
To keep your Ultimaker 2+ in optimal condition we recommend the following maintenance schedule, based on 1,500 printing hours per year:
Every month | Every three months | Every Year |
---|---|---|
Clean Printer | Check for plays on axels | Clean feeder and replace Bowden tube |
Lubricate axles | Check for tension of short belts | |
Lubricate lead screw Z moto | ||
Re-tighten hot end isolator |
Releasing clocked material from nozzle
Over time filament will block the nozzle. to clean the nozzle follow the following steps:
- Remove remaning filament
- Get a 30cm of Nylon filament and straighten it as much as possible
- Remove the blue horshoe clip underneath the white coupling
- Remove the filament tube out of the print head, while holding the white coupling
- Select in the main menu Advanced
- Select Heatup Nozzle
- Raise the nozzle temperature to 260 degrees
- Once on right temperature, insert the straightened piece of filament in the nozzle
- Set the temperature to 90 degrees and wait for the printer to reach this temperature
- Pull out the filament, be aware may require substantial force
- Repeat this process as often as required
See also:
Manual and procedures
For supplier manuals see:
Settings
See Materials for description of materials which can be printed
Setting | PLA | ABS | PETG |
---|---|---|---|
Printing temperature | - | 250 °C | - |
Printing table temp. | - | 110 °C | - |
Printing speed | 60 mm/s | 25 mm/s | - |
Fan speed | 100% | 20% | - |
Printing on the Ultimaker 2 + or Ultimaker 2 Extended +
To print a 3D model:
- Prepare the GCODE file and copy it to a SD card
- Enter the SD card into the SD card reader
- Prepare the print table for printing, apply
- glue (for PLA) or
- painters tape (for ABS)
- Switch on Ultimaker on the back side of the machine
- Change material:
- To change material or the enter material in to the printer, choose Material in the main menu
- Choose Change. The machine heats up and first will remove existing material
- Choose Ready once material is removed
- Feeding new Material
- Feed new material on the back side of the UltiMaker
- Choose Ready once the material is transported through the tube. The material will be transported to the nozzle.
- Wait till material flows through nozzle and confirm by selecting Ready
- Return to main menu by selection Return
- Print model
- Select Print
- Choose model you like to print. The printer heats up to the required temperature.
- Printing
- Once the nozzle and print table are at th erequired temperature, the printer will start.
- Printer releases small amount of filament through the nozzle
- The printer starts printing
- The display shows the expected time for the print
- Print ready
- Allow the printer table to cool down. Too early removal of the print may damage the print
- Remove the print from the print table
- Clean the printer table when required (remove glue / painter tape)
- Remove the Filament from the printer by executing step 3 of this procedure
- Once the filament is removed, switch off the print with the switch on the backside of the printer
- Store filament in the appropriate location