Router Table Wood / Tafelfrees hout

General

This equipment is safety category 3:

• Mandatory, in person, instructions.
  
• Make sure you read the Wiki before asking.

This equipment is Noise Category 2:
Can be used at all hours, but in moderation.
Be considerate; if you feel you need to wear ear protection,
then only use the tool between 07:00 and 19:00.

This equipment MUST be used with active dust control:

• Connect a shop-vac prior to use and keep it on while using it.
• Let it run for 10-20 seconds post use.

Not doing so endangers the operator, others, the space and the equipment.

Regarding the DeWalt Wood Chip Extractor:

• Do not fill the bag past 2/3rd of its capacity.
• Check for enough airflow before using the connected tool.
• Check that there is no (hot/smoldering) wood in the bottom of the machine when you smell something.

The large router table has a high-power inverted router (Triton TRA001, 2400 W) on an insert plate (Marman Tools IP2.0K-TRI).

Triton TRA001 2400 W router used in the table

The router table is currently still under construction and NOT yet in use. Would you like to help with the next steps? Please!

Below is a list of the to-do's; for further information contact Ruud or Hedde.

Setup

The current setup was made by Ruud, Thomas and Hedde. Initially the table was made for a hand-made insert (by Alex) with a Bosch router, but the current insert and router were purchased new. The table was designed so that it is mobile (large lockable wheels) and has the same height as the large saw table. As such it can serve as support for the saw table and the saw table can be used as support for large pieces for the router.

Maman Tools IP2.0K-TRI

The router is a Triton TRA001 2400 W (see Manufacturer website). The insert plate is from Marman Tools IP2.0K-TRI (see manufacturer website). Please note:

• The router is VERY powerful, be CAREFUL
• ALWAYS move the piece in the direction of the arrow
• Always adjust the amount of material you take off : doing many shallow passes can be tedious but trying to do it in one go and having the piece fly to your face is significantly more inconvenient
• The router speed can and should be adjusted (bigger bits such as chamfer bits need to spin slower due to their bigger diameter). The speed regulation wheel is located behind the router (not very easy to access)
• There are 2 different size reduction plates for large and small bits
• Remove the reduction plate (held in place magnetically) to change bits
• There are screws to flush the insert plate AND for the reduction plate

The router table is still under construction, the following steps still need to be taken (14 july 2023):

1. Electrical control box and connection with tag
2. Finish 2 lower large drawers, make fronts + pull mechanism for all drawers (see 7.)
3. Make a door for the router (thick plexiglass if available), done by Henk - thanks!
4. Add holes in back and check dust suction with test runs (attach to big suction system in place of small router table)
5. Test runs (initial tests have been done 18-6 and seem OK)
   NB: Make sure to NOT tighten the collet without a bit; the collet can get stuck!
6. Test Finger boards and add ons
7. Make fronts for drawers and door for cabinet top right
8. Organize everything and update this wiki-page
9. Formulate instructions and add to permissions system + give instructions
10. Move stuff in cabinet back-right, sort, talk to members and Hans D (it's mosltly his stuff) where this should go, re-organize and move new router table in place of cabinet with old router table (is also owned by Hans D) on top

NB: Hedde is on vacation 16-7 until 16-8; please continue with above. Talk to Valere and / or Ruud about it.

Do YOU want to help with any or all of the above? PLEASE! Contact Hedde or Ruud. Or just mail to all deelnemers.

Basic rules

The router table is currently not yet in use, please use the Router_Table_/_Tafelfrees if you want to do inverted routing. (or the Makita hand router)

Mandatory notifications

1. Whoever uses this *must* notify other members if there are disruptions or defects
2. Accidents and near-accidents must be be notified to other members (anything more than a small bandaid)

Before use

1. You can only use the router table after you've had instructions (see below + in person needed)
2. Check if the machine is clean and nothing seems broken

Wat betreft de machine schoon en veilig achterlaten - per algemene makerspace regel is dit altijd de verantwoordelijkheid van de *laatste* gebruiker. Dus als je de troep van een ander niet wil opruimen; meld het dan - en gebruik de machine niet. Zodra je iets gebruikt ben je verantwoordelijk voor het in goede en schone staat achterlaten van de machine; en het melden van storingen of defecten.

Use

...TBA...

After use

1. Clean the machine well, also the sawdust accumulated around the router
2. ...

Instructions

People who can give instructions are:

1. ...
2. ...

Instructions consist of ... TBA

Email with problems and defects to: deelnemers@makerspaceleiden.nl

Email with accidents to: bestuur@makerspaceleiden.nl