Router table 2023

Safety Sheet router table

General

This equipment is safety category 3:

• Mandatory, in person, instructions.
  
• Make sure you read the Wiki before asking.

This equipment is Noise Category 2:
Can be used at all hours, but in moderation.
Be considerate; if you feel you need to wear ear protection,
then only use the tool between 07:00 and 19:00.

Router table

Triton TRA001 2400 W router used in the table

The large router table has a high-power inverted router (Triton TRA001, 2400 W) on an insert plate (Marman Tools IP2.0K-TRI).

The router table can now be used. We have a complete set of 5 collets for this router. Including three sizes of metric (6mm, 8mm, and 12mm) and two sizes of imperial (¼" and ½"). Check the size of your router bits! Do not try to use an imperial bit in a metric collet, and visa versa. Make sure you have the correct collet for the bit you are using. The imperial collets are largely only needed if you bought your bits from the US.

Keep in mind that this is a new machine and that there is no extensive experience feedback about it yet.

Stay focused and alert when using it.

Below is a list of further to-do's; for further information contact Ruud or Hedde.

Accessories

Router collets in 3d printed holder

Collets

We have the full set of 5 collets for this device. They are stored in a green holder in the top left drawer. It is critical that you choose the correct collet for your router bit. This is most important with the 6mm vs ¼" and the 12mm vs ½" collets. If you put the wrong size bit in you risk breaking the collet, or worse, not clamping the bit correctly and producing spinning shrapnel of death. Router bits should have markings on them telling you the shank size, and thus the correct collet to use. Generally leave the 8mm collet fitted to the machine, as that is the most common size used in Europe. The holder has markings for the different sizes, do not trust that the right collet is in the right slot, double check you are using the correct one. Each collet is printed on the top face with the size.

• 6mm collet
• ¼" collet
• 8mm collet
• 12mm collet
• ½" collet

(note the ½" collet is currently not in the holder pending degreasing)

Bits

Router bits laying on the router table

There are a number of router bits available for use with the router table. These are provided as is, with nothing to guarantee they are sharp, they are present, and that they will work. If you want to be absolutely certain that a specific type of bit is available, it's best to buy your own bit. They can be purchased from various places including toolstation, ecotools, fine tools, dictum, and sauter shop. For more info on purchasing, see the Leveranciers page. The list of available bits, at the time of writing is:

• Rebate bit (cuts a 6.35mm rebate into edge of work piece)
• Spiral pattern bit (12mm)
• Spiral bit (6mm)
• bowl bit (19mm)
• 45° chamfer bit with bearing
• long straight pattern bit

There is also a box of Bosch router bits which is stored on the shelf above the small wood working machines. This is shared with the hand held routers, make sure they go back where they came from.

Other

In the top let drawer there is spanner for tightening the collet. As well as a handle for adjusting the cutter height. There are also two steel plates that cover the area around the collet. Make sure you use the correct cover plate.

In the second drawer down there are various feather boards. These are to keep your workpiece in place while you cut it. They don't necessarily read far enough to hold thin or small stock. You may find that it helps to use double sided tape to anchor a piece of scrap to thin pieces to provide better registration against the fence.

Setup

The current setup was made by Ruud, Thomas and Hedde. Initially the table was made for a hand-made insert (by Alex) with a Bosch router, but the current insert and router were purchased new. The table was designed so that it is mobile (large lockable wheels) and has the same height as the large tablesaw. As such it can serve as (additional) support for the sawtable and vice versa the tablesaw can be used as support for large pieces you may want to pass along the inverted router on the router table.

Marman Tools IP2.0K-TRI insert plate

The router is a Triton TRA001 2400 W (see Manufacturer website). The insert plate is from Marman Tools IP2.0K-TRI (see manufacturer website). Please note:

• The router is VERY powerful, be CAREFUL
• NEVER WEAR GLOVES when working on the machine
• ALWAYS move the piece in the direction of the arrow (right to left) : climb cutting is prohibited with this machine for obvious safety reasons.
• Be careful when routing endgrain : always try to support the piece close to the router bit (but not with your hand of course, use the pushstick from the table saw for instance)
• Always adjust the amount of material you take off : doing many shallow passes can be tedious but trying to do it in one go and having the piece fly to your face or having a chunk of wood get ripped off your piece is significantly more inconvenient.
• The router speed can and should be adjusted (bigger bits such as chamfer/roundover bits need to spin slower due to their bigger diameter). The speed regulation wheel is located behind the router (not very easy to access)
• There are 2 different size reduction plates for large and small bits.
• Remove the reduction plate (held in place magnetically) to change bits
• There are screws to flush the insert plate AND for the reduction plate

The router table is still under construction, the following steps still need to be taken (14 July 2023 / update 23rd Jan 2024)):

1. No tag needed as per June 2023 deelnemers meeting - done
2. Finish 2 lower large drawers, make fronts + pull mechanism for all drawers (see 7.)
3. Plexiglass door created by Henk - thanks! - done
4. Suction hose connected. - done
5. Initial tests have been.NB Make sure to NOT tighten the collet without a bit; the collet can get stuck!
6. Test fingerboards and add-ons - done
7. Make fronts for drawers and door for cabinet top right
   
8. Organize everything and update this wiki-page - wip
9. Formulate instructions and add to permissions system + give instructions - done
10. Move stuff in cabinet back-right, sort, talk to members and Hans D (it's mosltly his stuff) where this should go, re-organize and move new router table in place of cabinet with old router table (is also owned by Hans D) on top

Do YOU want to help with any or all of the above? PLEASE! Contact Hedde or Ruud. Or just mail to all deelnemers.

Mandatory notifications

1. Whoever uses this *must* notify other members if there are disruptions or defects
2. Accidents and near-accidents must be be notified to other members (anything more than a small bandaid)

Before use

1. You can only use the router table after you've had instructions (see below + in person needed)
2. Check if the machine is clean and nothing seems broken

Wat betreft de machine schoon en veilig achterlaten - per algemene makerspace regel is dit altijd de verantwoordelijkheid van de *laatste* gebruiker. Dus als je de troep van een ander niet wil opruimen; meld het dan - en gebruik de machine niet. Zodra je iets gebruikt ben je verantwoordelijk voor het in goede en schone staat achterlaten van de machine; en het melden van storingen of defecten.

Use

1. Put on safety glasses at the very least, hearing protection recommended
2. Attach the dust extraction hose to the back of the cabinet/fence
3. Use the crank handle to bring the router all the way up
4. Insert a bit into the collet and tighten with the spanner (do not overtighten)
5. Setup the router height with the spanner (and remove the crank handle when done)
6. If using a big bit, adjust the rotation speed by reaching under the router on the other side. If you rotate all the way to the left, the speed is at the minimum, and to the right at the maximum (TBC ?)
7. If needed, adjust the fence
8. If needed, you can use fingerboards to keep your workpiece tight against the fence + reduce the risk of kickback
9. Perform a visual check that nothing is in contact with the bit
10. Make sure the front door is closed
11. Start the machine with the switch on the right side of the machine
12. If the sound does not seem right or if you can feel vibrations, stop the machine immediately
13. If you need to route multiple pieces with the same setup, turn off the machine between each pass

After use

1. Clean the machine well, also the sawdust accumulated around the router
2. Put the crank handle and spanner in the upper left drawer
3. Remove and clean finger boards. Store them in left drawer.

Instructions

People who can give instructions are listed on the machine page in the CRM.

Instructions consist of an in-person introduction to the safety aspects of the machine as well as best-practice uses.

Email with problems and defects to: deelnemers@makerspaceleiden.nl

Email with accidents to: bestuur@makerspaceleiden.nl