ToDo: verschil tussen versies
(→Blue Laser engraver/cutter) |
(→red laser engraver/cutter) |
||
Regel 13: | Regel 13: | ||
=== red laser engraver/cutter === | === red laser engraver/cutter === | ||
* Might need maintainance / cleaning (dust. Mirrors and lens are clean, but everything else is dusty), but should be usable | * Might need maintainance / cleaning (dust. Mirrors and lens are clean, but everything else is dusty), but should be usable | ||
+ | ** From Millie: "kleine kastje gaat niet aan" - so possibly a losse connection to the LCD/control panel. | ||
* put config file on github | * put config file on github | ||
* update wiki with new visicut | * update wiki with new visicut |
Versie van 6 jun 2019 om 22:02
We maintain the space collectively - as an all volunteer effort.
Inhoud
Physical things
New dust control for the wood workshop: Succobus
- Tubing:
Put short pipes on each T junction behind each machine; then the Valve, then a short pipe and then a bit of hose of the right length.Secure with hose clamps. We'll need to make a few wooden/plastic adaptors on the lathe to get the diameters right.
- Electrics:
Run a 3 phase cable from behind the bandsaw over the wood-storage area to the Succobus box.Wire up the 3 phase with the slow-starter & wire the slowstart to the control box.- Feed the bare-copper wire through all the tubes -- to stop static dust collection.
red laser engraver/cutter
- Might need maintainance / cleaning (dust. Mirrors and lens are clean, but everything else is dusty), but should be usable
- From Millie: "kleine kastje gaat niet aan" - so possibly a losse connection to the LCD/control panel.
- put config file on github
- update wiki with new visicut
Blue Laser engraver/cutter
- Specialist work. Don' t undertake unless comfortable and capable. See Blue_laser_engraver
- correct fan wire in power supply contacting fan blades making noise
check high voltage wiring connections to the laser tubeCheck / listen to it under power. (There is a weird hiss at lower PWM values)shorten the blauwe snuffelit currently runs "test" firmware, check that buttons/motors function as they should(X motor / Y motor / Y endstop works. X endstop does not respond. User control buttons/display work.)
repair X endstop AGAINDone, worksverify it homes in the right directionIO-test firmware seems not to use config. Configure later.test/calibrate A-meter and Set max. lasertube current (2 person job for safety reasons).once all is OK, flash "use" firmware(re)place SD card (with a good 2GB FAT formated one)Done!test and make notes of everything weirdallign mirrors (from the first one, again. Because error adds up)make sure the dimensions / steps per unit etc. are correct (so 1mm realy results in 1mm)whitin reason.Visicut and machine have different ideas about what is left and right and origin. Investigate, mediate, and unify.
- non-dangerous work:
- update Blue_laser_engraver (Add a picture)
- Honingraatbed?
- Top-up the cooling water (with demineralized 'laser' water with a drop of the 'no-green-stuff--stuff')
- improve network connection (Already on NetworkSetup#IP but machine itself needs to be configured accordingly. Currently it has a set IP and no DHCP, new config should be DHCP and it will get a static IP)
Ventilation slot covers that let air trough but require light to bend in impossible ways, so the laser stays in.Put config files on github(Also for the red one, and maybe compare them?)
lights
- Hang the warmer lights in the small room (preferably before Hans returns! as he donated them.)
- We might need to get cable etc. first
Wiring
Affix the dangling small 2 port junction box to the concrete slab above the space door. Plug's are in a box labeled thus in the green cabinet; the big green metabo drill in the woodshop can be set to hammering.
recurring
- vacuüm small room
- And maybe the larger one too (or use a broom)
- Dishes
- clean kitchen
- clean toilet
- put bin out on the right day - volunteer in CRM
Documentation things
- Update the wiki to describe the second garbage bin processes.
- We have quite a few Tools without foto's or where we use bland photos from HBM. To replace. Ideally in situ so you know where things are.
- Video of an expert (e.g. HansD) replacing & adjusting the knifes on the planer/jointer with the special tool.
Cyber Things
- Add OpenID or similar to the CRM and push/wire this up to wordpress and the wiki.
- Find and install crosspost module on wordpress to twitter/facebook.
- See if we can do post-by-email or simpler for wordpress.
repairs
floor
- fix holes in floor in large room (with the right kind of concrete / get it somewhat level and evenly)
- procure/find/ask shops for scraps a piece of linoleum for the small room. Same thickness, any color. About .. cm wide / .. m long. Or smaller pieces that add up. Also glue and filament (for the seams).
- put it all in place, fixing the "gutter" in front of E-table.
electric
- There is one outlet left of the abene that does not work, possibly a loose wire?
- We 're out of 12V halogen bulbs for the small desklights (But the white/translucent one has had it's bulb replaced with the last spare)