ToDo: verschil tussen versies

Uit MakerSpace Leiden
Ga naar: navigatie, zoeken
(→‎checkout node)
 
(82 tussenliggende versies door 7 gebruikers niet weergegeven)
Regel 1: Regel 1:
 +
[[Category:Algemeen]]
 +
 +
 
We maintain the space collectively - as an all volunteer effort.
 
We maintain the space collectively - as an all volunteer effort.
  
−
== Physical things ==
+
==recurring==
 +
 
 +
* vacuüm small room
 +
* And maybe the larger one too (or use a broom)
 +
* Dishes
 +
* clean kitchen
 +
* clean toilet
 +
* Clean and reoil the various metal working machines - including a thin coat of slideways-oil / lijbaan olie on the gangways/slides/lijbanen.
 +
* Return misplaced tools to where they belong.
 +
* Specialist: clean LaserSaur (& Red&Blue engravers) Mirrors
 +
* Clean lasersaur bed
 +
* Clean air filter
 +
 
 +
Tasks that the CRM will email about:
 +
 
 +
* put bin out on the right day - volunteer in CRM
 +
* Check compressors (Water seperators and condensation outlet)- volunteer in CRM
 +
* Check drillbits (3x) and replenish from the green storage/bulk box - volunteer in CRM
 +
* Refill the various [[SnijOlie BoorOlie CuttingOil]] bottles - volunteer in CRM
 +
 
 +
==Physical things==
 +
===Small jobs===
 +
 
 +
* Vaccuum-clean small room.
 +
* Sort Plastic Stash under lasersaurus: Un-laserable PolyCarbonate is now mixed in with the laserable Acrylic. Move un-laserable PC (To where? Algemene voorraadkast? Lasersaurkast because it is what the saur is made of? Something Frees-ish because usable with frees?)
 +
* Inkorten alle zwarte slangen perslucht (Alex/Jan zijn slangpilaartjes aan het bestellen,
  
 
===New dust control for the wood workshop: [[Succobus]]===
 
===New dust control for the wood workshop: [[Succobus]]===
 
* Tubing:
 
* Tubing:
−
** <strike>Put short pipes on each T junction behind each machine; then the Valve, then a short pipe and then a bit of hose of the right length. </strike> Secure with hose clamps. We'll need to make a few wooden/plastic adaptors on the lathe to get the diameters right.
+
** <s>Put short pipes on each T junction behind each machine; then the Valve, then a short pipe and then a bit of hose of the right length. </s> Secure with hose clamps. We'll need to make a few wooden/plastic adaptors on the lathe to get the diameters right.
 +
 
 
* Electrics:
 
* Electrics:
−
** <strike>Run a 3 phase cable from behind the bandsaw over the wood-storage area to the Succobus box. </strike>
 
−
** <strike>Wire up the 3 phase with the slow-starter & wire the slowstart to the control box.</strike>
 
 
** Feed the bare-copper wire through all the tubes -- to stop static dust collection.
 
** Feed the bare-copper wire through all the tubes -- to stop static dust collection.
  
−
=== checkout node ===
+
===Blue Laser engraver/cutter===
−
* <s>Run 3 ethernet cables to the space-door for the checkout node; and touch screen/etc.</s>
+
* Is defect, moet worden gerepareerd. Mogelijk voeding.
−
* <s>Terminate the loose ethernet cable and figure out where they go.<s>
 
  
−
=== red laser engraver/cutter ===
+
===Saurus===
−
* Might need (specialist) maintainance (Is the lens clean?) but should otherwise be usable
 
−
* put config file on github
 
−
* update wiki with new visicut
 
  
−
=== Blue Laser engraver/cutter ===
+
* Side panel for electronics is missing, they now get dusty. Clean & replace.
−
* Specialist work. Don' t undertake unless comfortable and capable. See [[Blue_laser_engraver]]
+
* Recurring: Cleaning. Cleaning mirrors is specialist work.
−
** <s>check high voltage wiring connections to the laser tube</s> Check / listen to it under power.
 
−
** <s>shorten the blauwe snuffel</s>
 
−
** <s>it currently runs "test" firmware, check that buttons/motors function as they should</s>
 
−
*** <s>(X motor / Y motor / Y endstop works. X endstop does not respond. User control buttons/display work.)</s>
 
−
** <s>repair X endstop AGAIN</s> Done, works
 
−
** <s>verify it homes in the right direction</s> <s>IO-test firmware seems not to use config. Configure later.</s>
 
−
** <s>test/calibrate A-meter and Set max. lasertube current (2 person job for safety reasons).</s>
 
−
** <s>once all is OK, flash "use" firmware</s>
 
−
** <s>(re)place SD card (with a good 2GB FAT formated one)</s> Done!
 
−
** test and make notes of everything weird
 
−
** correct fan wire in power supply contacting fan blades making noise
 
−
** allign mirrors (from the first one, again. Because error adds up)
 
−
** make sure the dimensions / steps per unit etc. are correct (so 1mm realy results in 1mm)
 
−
** Visicut and machine have different ideas about what is left and right and origin. Investigate, mediate, and unify.
 
  
−
* non-specialist work:
+
===Wiring===
−
** update [[Blue_laser_engraver]] (Add a picture)
+
* Wire the lamp above the metal work table to the TL lights in the ceiling.
−
** Honingraatbed?
+
* Find higher power tubes that do not flicker for that fitting.
−
** Ventilation slot covers that let air trough but require light to bend in impossible ways, so the laser stays in.
 
−
** Put config files on github (Also for the red one, and maybe compare them?)
 
  
−
=== lights ===
+
===Network===
−
* Hang the warmer lights in the small room (preferably before Hans returns! as he donated them.)
+
<s># Remove all VLANs and flatten the network to one.</s>
−
** We might need to get cable etc. first
+
# Update docs how how we did the firewall, etc. -- see [[2020 grote opruiming netwerk]]
  
−
=== Wiring ===
+
===Metaal werkplaats===
 +
<s># werktafel aan vloer zetten</s>
 +
# 4x L Beugeltjes maken om de poten van de werktafel beter aan de 4 keilbouten vast te zetten
  
−
Affix the dangling small 2 port junction box to the concrete slab above the space door. Plug's are in a box labeled thus in the green cabinet; the big green metabo drill in the woodshop can be set to hammering.
+
==Documentation things==
  
−
=== recurring ===
 
−
* vacuüm small room
 
−
* And maybe the larger one too (or use a broom)
 
−
* Dishes
 
−
* clean kitchen
 
−
* clean toilet
 
−
* put bin out on the right day - volunteer in CRM
 
−
 
−
== Documentation things ==
 
 
* Update the wiki to describe the second garbage bin processes.
 
* Update the wiki to describe the second garbage bin processes.
−
* We have quite a few [[:Categorie:Tool|Tools]] without foto's or where we use bland photos from HBM. To replace. Ideally in situ so you know where things are.
+
* We have quite a few [[:Categorie:Tool|Tools]] without foto's or where we use bland photos from HBM. To replace. Ideally in situ so you know where things are.
 
* Video of an expert (e.g. HansD) replacing & adjusting the knifes on the planer/jointer with the special tool.
 
* Video of an expert (e.g. HansD) replacing & adjusting the knifes on the planer/jointer with the special tool.
 +
* put config files for the laos lasercutters on github
 +
* update wiki with new visicut
  
−
== Cyber Things ==
+
==Cyber Things==
  
 
* Add OpenID or similar to the CRM and push/wire this up to wordpress and the wiki.
 
* Add OpenID or similar to the CRM and push/wire this up to wordpress and the wiki.
Regel 70: Regel 72:
 
* See if we can do post-by-email or simpler for wordpress.
 
* See if we can do post-by-email or simpler for wordpress.
  
−
== repairs ==
+
==repairs==
 +
 
 +
 
 +
 
 +
===floor===
  
−
=== floor ===
 
 
* fix holes in floor in large room (with the right kind of concrete / get it somewhat level and evenly)
 
* fix holes in floor in large room (with the right kind of concrete / get it somewhat level and evenly)
−
* procure/find/ask shops for scraps a piece of linoleum for the small room. Same thickness, any color. About .. cm wide / .. m long. Or smaller pieces that add up. Also glue and filament (for the seams).
 
−
** put it all in place, fixing the "gutter" in front of E-table.
 
  
−
=== electric ===
+
===electric===
−
* There is one outlet left of the abene that does not work, possibly a loose wire?
+
 
−
* We 're out of 12V halogen bulbs for the small desklights (But the white/translucent one has had it's bulb replaced with the last spare)
+
* <s>There is one outlet left of the abene that does not work, possibly a loose wire?</s> Fixed. But can be pulled out of the wall with the plug. That' s left for someone else to fix.

Huidige versie van 28 dec 2023 om 18:07


We maintain the space collectively - as an all volunteer effort.

recurring

  • vacuüm small room
  • And maybe the larger one too (or use a broom)
  • Dishes
  • clean kitchen
  • clean toilet
  • Clean and reoil the various metal working machines - including a thin coat of slideways-oil / lijbaan olie on the gangways/slides/lijbanen.
  • Return misplaced tools to where they belong.
  • Specialist: clean LaserSaur (& Red&Blue engravers) Mirrors
  • Clean lasersaur bed
  • Clean air filter

Tasks that the CRM will email about:

  • put bin out on the right day - volunteer in CRM
  • Check compressors (Water seperators and condensation outlet)- volunteer in CRM
  • Check drillbits (3x) and replenish from the green storage/bulk box - volunteer in CRM
  • Refill the various SnijOlie BoorOlie CuttingOil bottles - volunteer in CRM

Physical things

Small jobs

  • Vaccuum-clean small room.
  • Sort Plastic Stash under lasersaurus: Un-laserable PolyCarbonate is now mixed in with the laserable Acrylic. Move un-laserable PC (To where? Algemene voorraadkast? Lasersaurkast because it is what the saur is made of? Something Frees-ish because usable with frees?)
  • Inkorten alle zwarte slangen perslucht (Alex/Jan zijn slangpilaartjes aan het bestellen,

New dust control for the wood workshop: Succobus

  • Tubing:
    • Put short pipes on each T junction behind each machine; then the Valve, then a short pipe and then a bit of hose of the right length. Secure with hose clamps. We'll need to make a few wooden/plastic adaptors on the lathe to get the diameters right.
  • Electrics:
    • Feed the bare-copper wire through all the tubes -- to stop static dust collection.

Blue Laser engraver/cutter

  • Is defect, moet worden gerepareerd. Mogelijk voeding.

Saurus

  • Side panel for electronics is missing, they now get dusty. Clean & replace.
  • Recurring: Cleaning. Cleaning mirrors is specialist work.

Wiring

  • Wire the lamp above the metal work table to the TL lights in the ceiling.
  • Find higher power tubes that do not flicker for that fitting.

Network

# Remove all VLANs and flatten the network to one.

  1. Update docs how how we did the firewall, etc. -- see 2020 grote opruiming netwerk

Metaal werkplaats

# werktafel aan vloer zetten

  1. 4x L Beugeltjes maken om de poten van de werktafel beter aan de 4 keilbouten vast te zetten

Documentation things

  • Update the wiki to describe the second garbage bin processes.
  • We have quite a few Tools without foto's or where we use bland photos from HBM. To replace. Ideally in situ so you know where things are.
  • Video of an expert (e.g. HansD) replacing & adjusting the knifes on the planer/jointer with the special tool.
  • put config files for the laos lasercutters on github
  • update wiki with new visicut

Cyber Things

  • Add OpenID or similar to the CRM and push/wire this up to wordpress and the wiki.
  • Find and install crosspost module on wordpress to twitter/facebook.
  • See if we can do post-by-email or simpler for wordpress.

repairs

floor

  • fix holes in floor in large room (with the right kind of concrete / get it somewhat level and evenly)

electric

  • There is one outlet left of the abene that does not work, possibly a loose wire? Fixed. But can be pulled out of the wall with the plug. That' s left for someone else to fix.
Overgenomen van "https://wiki.makerspaceleiden.nl/mediawiki/index.php?title=ToDo&oldid=12705"