ToDo: verschil tussen versies
(→Documentation things) |
|||
Regel 3: | Regel 3: | ||
== Physical things == | == Physical things == | ||
− | + | ===New dust control for the wood workshop: [[Succobus]]=== | |
− | + | * Tubing: | |
− | + | ** Put short pipes on each T junction behind each machine; then the Valve, then a short pipe and then a bit of hose of the right length. Secure with hose clamps. We'll need to make a few wooden/plastic adaptors on the lathe to get the diameters right. | |
− | + | * Electrics: | |
− | + | ** Run a 3 phase cable from behind the bandsaw over the wood-storage area to the Succobus box. | |
− | + | ** Wire up the 3 phase with the slow-starter & wire the slowstart to the control box. | |
− | + | * Collector: | |
− | + | ** Figure out of/how we put a thin dust collector above the separator. | |
− | + | ** Mount this on the wall. | |
− | + | ** Check if we need to remove the 90 degree angles/replace by 3x30 to get better flow. | |
− | + | ** See if we need to attach the separate to the wall - and het the drum 'drop' down below it. | |
+ | === checkout node === | ||
* Run 3 ethernet cables to the space-door for the checkout node; and touch screen/etc. | * Run 3 ethernet cables to the space-door for the checkout node; and touch screen/etc. | ||
* Terminate the loose ethernet cable and figure out where they go. | * Terminate the loose ethernet cable and figure out where they go. | ||
− | * | + | |
+ | === Blue Laser engraver/cutter === | ||
+ | * Specialist work. Don' t undertake unless comfortable and capable. See [Blue_laser_engraver] | ||
+ | ** check high voltage wiring connections to the laser tube | ||
+ | ** it currently runs "test" firmware, check that buttons/motors function as they should | ||
+ | ** Set max. lasertube current (2 person job for safety reasons). | ||
+ | ** once all is OK, flash "use" firmware | ||
+ | ** test | ||
+ | |||
+ | * non-specialist work: | ||
+ | ** update [Blue_laser_engraver] (Add a picture) | ||
+ | |||
+ | === floor === | ||
+ | * fix holes in floor in large room (with the right kind of concrete / get it somewhat level and evenly) | ||
+ | * procure/find/ask shops for scraps a piece of linoleum for the small room. Same thickness, any color. About .. cm wide / .. m long. Or smaller pieces that add up. Also glue and filament (for the seams). | ||
+ | ** put it all in place, fixing the "gutter" in front of E-table. | ||
+ | |||
+ | === lights === | ||
+ | * Hang the "gezellige" lights in the small room (preferably before Hans returns! as he donated them.) | ||
+ | ** We might need to get cable etc. first | ||
+ | |||
+ | === recurrent === | ||
+ | * vacuüm small room | ||
+ | * And maybe the larger one too (or use a broom) | ||
+ | * Dishes | ||
+ | * clean kitchen | ||
+ | * clean toilet | ||
== Documentation things == | == Documentation things == | ||
− | + | * Update the wiki to describe the second garbage bin processes. | |
* We have quite a few [[Category::Tools]] without foto's or where we use bland photos from HBM. To replace. Ideally in situ so you know where things are. | * We have quite a few [[Category::Tools]] without foto's or where we use bland photos from HBM. To replace. Ideally in situ so you know where things are. | ||
* Video of an expert (e.g. HenkD) replacing & adjusting the knifes on the planer/jointer with the special tool. | * Video of an expert (e.g. HenkD) replacing & adjusting the knifes on the planer/jointer with the special tool. |
Versie van 18 apr 2019 om 19:14
We maintain the space collectively - as an all volunteer effort.
Inhoud
Physical things
New dust control for the wood workshop: Succobus
- Tubing:
- Put short pipes on each T junction behind each machine; then the Valve, then a short pipe and then a bit of hose of the right length. Secure with hose clamps. We'll need to make a few wooden/plastic adaptors on the lathe to get the diameters right.
- Electrics:
- Run a 3 phase cable from behind the bandsaw over the wood-storage area to the Succobus box.
- Wire up the 3 phase with the slow-starter & wire the slowstart to the control box.
- Collector:
- Figure out of/how we put a thin dust collector above the separator.
- Mount this on the wall.
- Check if we need to remove the 90 degree angles/replace by 3x30 to get better flow.
- See if we need to attach the separate to the wall - and het the drum 'drop' down below it.
checkout node
- Run 3 ethernet cables to the space-door for the checkout node; and touch screen/etc.
- Terminate the loose ethernet cable and figure out where they go.
Blue Laser engraver/cutter
- Specialist work. Don' t undertake unless comfortable and capable. See [Blue_laser_engraver]
- check high voltage wiring connections to the laser tube
- it currently runs "test" firmware, check that buttons/motors function as they should
- Set max. lasertube current (2 person job for safety reasons).
- once all is OK, flash "use" firmware
- test
- non-specialist work:
- update [Blue_laser_engraver] (Add a picture)
floor
- fix holes in floor in large room (with the right kind of concrete / get it somewhat level and evenly)
- procure/find/ask shops for scraps a piece of linoleum for the small room. Same thickness, any color. About .. cm wide / .. m long. Or smaller pieces that add up. Also glue and filament (for the seams).
- put it all in place, fixing the "gutter" in front of E-table.
lights
- Hang the "gezellige" lights in the small room (preferably before Hans returns! as he donated them.)
- We might need to get cable etc. first
recurrent
- vacuüm small room
- And maybe the larger one too (or use a broom)
- Dishes
- clean kitchen
- clean toilet
Documentation things
- Update the wiki to describe the second garbage bin processes.
- We have quite a few [[Category::Tools]] without foto's or where we use bland photos from HBM. To replace. Ideally in situ so you know where things are.
- Video of an expert (e.g. HenkD) replacing & adjusting the knifes on the planer/jointer with the special tool.
Cyber Things
- Add OpenID or similar to the CRM and push/wire this up to wordpress and the wiki.
- Find and install crosspost module on wordpress to twitter/facebook.
- See if we can do post-by-email or simpler for wordpress.