VNA - Vector Network Analyser: verschil tussen versies
| (19 tussenliggende versies door 2 gebruikers niet weergegeven) | |||
| Regel 1: | Regel 1: | ||
| − | [[Category: | + | [[Category:Tools]][[Category:Electronics tools]] |
{{NoiseCat3}} {{SafetyCat5}} | {{NoiseCat3}} {{SafetyCat5}} | ||
[[Bestand:Vna-box.jpg|miniatuur]] | [[Bestand:Vna-box.jpg|miniatuur]] | ||
| − | [[Bestand:Vna- | + | [[Bestand:Vna-box2.jpg|miniatuur]] |
| − | Vector Network Analyser - possible manuals [[Bestand:Vna-manual1.pdf| | + | == Manuals == |
| + | |||
| + | Vector Network Analyser - possible manuals: | ||
| + | |||
| + | [[Bestand:Vna-manual1.pdf|100px]][[Bestand:Vna-manual2.pdf|100px]]. | ||
| + | |||
| + | Currently in a box with 0802 capacitors that are suitable for [[RC522 RFID|RC522 RFID tuning]]. | ||
| + | |||
| + | == Location == | ||
| + | |||
| + | Electronics section, shelf under the [[Elektronica Onderdelen|components drawers]] in a wooden box. | ||
| + | |||
| + | == Box content == | ||
| + | [[Bestand:Vna-cover.png|400px|miniatuur]] | ||
| + | |||
| + | # VNA analyser up to 900 Mhz | ||
| + | # One USB-A/USB-C cable for charging and fetching graphs | ||
| + | # 2 SMA to SMA cables, male | ||
| + | # <strike>One SMA male to U.FL male</strike> | ||
| + | # One closed connector, 0 ohm for calibration | ||
| + | # One 50 ohm terminator, for calibration | ||
| + | # One open connector, for calibration | ||
| + | # One inter SMA to SMA connector | ||
| + | # SMA male to cable top solder to boards | ||
| + | # A range of 1p-1nF capacitors to help with [[RC522 RFID|turning MFRC522/RFC522 RFID readers]]. Larger capacitors are [[SMD Capacitors|also available]] | ||
| + | |||
| + | == Making off == | ||
| + | |||
| + | Files used to create the box: [[Bestand:Via-cut.svg|100px]] and [[Bestand:Via-cover.pdf|100px]]. | ||
| + | |||
| + | == Todo == | ||
| + | |||
| + | Redo the foam in the box to fit the SMA cables, make the connector slot less deep & make the capacitor slots a bit bigger. | ||
Huidige versie van 17 nov 2024 om 20:59
This equipment is Noise Category 3: Can be used at all hours. No limits.
This equipment is safety category 5: Equipment that is relatively fragile or expensive
- In person instructions is not mandatory.
- Reading the wiki, and following the instructions, is mandatory.
Manuals
Vector Network Analyser - possible manuals:
.
Currently in a box with 0802 capacitors that are suitable for RC522 RFID tuning.
Location
Electronics section, shelf under the components drawers in a wooden box.
Box content
- VNA analyser up to 900 Mhz
- One USB-A/USB-C cable for charging and fetching graphs
- 2 SMA to SMA cables, male
One SMA male to U.FL male- One closed connector, 0 ohm for calibration
- One 50 ohm terminator, for calibration
- One open connector, for calibration
- One inter SMA to SMA connector
- SMA male to cable top solder to boards
- A range of 1p-1nF capacitors to help with turning MFRC522/RFC522 RFID readers. Larger capacitors are also available
Making off
Files used to create the box: 
and 
.
Todo
Redo the foam in the box to fit the SMA cables, make the connector slot less deep & make the capacitor slots a bit bigger.
