SAFETY: verschil tussen versies

Uit MakerSpace Leiden
Ga naar: navigatie, zoeken
(Category 2)
(Category 3)
Regel 126: Regel 126:
 
== Category 3 ==
 
== Category 3 ==
 
{{NoiseCat3}}
 
{{NoiseCat3}}
[[Categorie:NoiseCat3]]
+
[[:Categorie:NoiseCat3]]
  
  
 
</translate>
 
</translate>

Versie van 26 okt 2018 om 19:43

Andere talen:
English

Veiligheid -- see the pages SafetySheet and NewMachine for info about adding stuff.

Verantwoordelijkheid / responsibility

The ultimate responsibility for a safe working environment and behavior lies with the board of the MakerSpace Leiden. This makes the situation different compared to working at home. You need to be aware of the safety of other people as well, not just yourself.

Participants should behave safely and report unsafe behaviors and situations to the board.

With a number of machines, it is mandatory to report certain faults or problems. This should be done as soon as possible; but at the latest within 24 hours. This is in the machine description.

General Safety Sheet] Makerspace Leiden

Index risico gereedschap

Risk categories:

  1. Highest' risk: mandatory instructions, [liability waiver] on file, approval from the trustees, two people present at all times - and can only be used between 07:00 and 19:00.
  2. High risk: Mandatory instructions, [liability waiver] on file, approval from the trustees, but Ok to operate alone.
  3. Mandatory instructions prior to use.
  4. Equipment that is dangerous - instructions strongly advised but not mandatory
  5. Equipment that is relatively fragile or expensive - so instructions strongly advised if you have not used them before - but not mandatory
  6. Other equipment with no limits - not considered overly dangerous.

Noise categories:

  1. Can only be used between 07:00 and 19:00
  2. Can be used outside those hours in moderation. But try to be considerate. And if you feel a need to wear ear protection - you are probably too noisy!
  3. No limits.

Safety categories

Category 1

This equipment is safety category 1 - the most dangerous class of machines.


Mandatory instruction is required.


The [liability waiver] needs to be on file and approval from the trustees is required (post instruction).
Two people present at all times.
Can only be used between 07:00 and 19:00 because of noise.

Category 2

This equipment is safety category 2:

  • Mandatory instructions.
  • [liability waiver] on file.
  • Approval from trustees, but ok to operate alone
(but be careful/ensure you have assistance when handling very large things).

:

Category 3

This equipment is safety category 3:

  • Mandatory, in person, instructions.
  • Make sure you read the Wiki before asking.

Category 4

This equipment is safety category 4:

  • In-person, instructions strongly advised but not mandatory.
  • Reading, and following, the instructions on the Wiki is mandatory!

Category 5

This equipment is safety category 5: Equipment that is relatively fragile or expensive

  • In person instructions is not mandatory.
  • Reading the wiki, and following the instructions, is mandatory.
  • Soldering equipment (air, tipped)
  • De-soldeerbout - lucht
  • Veneer calipers
  • Various cutters for the Abene mill.
  • Ritser - diamandpunt voor onderhoud slijpstenen.
  • Labvoedingen - power supplies on the workbench (they go up to about 100 volt & 10 amps).

Category 6

This equipment is safety category 6: Other equipment with no limits.

Noise categories

Category 1

This equipment is Noise Category 1: can only be used between 07:00 and 19:00.
Wear hearing protection.

Categorie:NoiseCat1

Category 2

This equipment is Noise Category 2:
Can be used at all hours, but in moderation.
Be considerate; if you feel you need to wear ear protection,
then only use the tool between 07:00 and 19:00.

[[::Categorie:NoiseCat2]]

Category 3

This equipment is Noise Category 3: Can be used at all hours. No limits.

Categorie:NoiseCat3