Tinzuiger / Desoldeerbout / Desoldering Pump: verschil tussen versies
(→Manual / use) |
|||
| (7 tussenliggende versies door dezelfde gebruiker niet weergegeven) | |||
| Regel 2: | Regel 2: | ||
{{NoiseCat3}}<br />{{SafetyCat4}} | {{NoiseCat3}}<br />{{SafetyCat4}} | ||
| − | |||
| − | + | [[Bestand:IMG 3107.jpg|300px]] | |
| + | [[Bestand:CleaningPins.jpg|300px|Cleaning pins]] | ||
| + | [[Bestand:DesolderBox.JPG|300px]] | ||
| + | |||
| + | Located at the soldering bench | ||
= Risks = | = Risks = | ||
| − | |||
| − | |||
Beware that you are handling molten metal. Consider wearing safetyglasses if things are likely to splatter. | Beware that you are handling molten metal. Consider wearing safetyglasses if things are likely to splatter. | ||
| − | + | Dont leave the machine turned on for a long time, the nozzle will corrode. | |
= Manual / use = | = Manual / use = | ||
| − | + | Manual in [[:Bestand:ZD-915 manual.pdf|English]] and in [[:Bestand:ZD-915 handleiding.pdf|Nederlands]] | |
| − | + | Short list with the key points for usage, read the manual for the complete instructions. | |
| + | |||
| + | * Turn on the device by pressing the red button. | ||
| + | * Select the temperature by pressing up/down buttons. Beware of the different between Celsius and Kelvin. | ||
| + | * Put the nozzle over the pin that should be cleaned and let the solder melt. | ||
| + | * Pull the trigger to suck the molten solder from the pin. | ||
| + | * After use the gun should be cleaned by sucking clean for a few times (3-5). Also use the cleaning pins to clean the nozzle, after using those pins also suck the residual solder from the nozzle. Solder that is left in the nozzle will damage the nozzle. | ||
= Maintenance = | = Maintenance = | ||
| − | + | After every usage the nozzle should be cleaned with a cleaning pin. | |
| + | |||
| + | The glass tube should be emptied once in a while, read the manual for instructions how to do this. | ||
| + | |||
| + | There is a box with extra cleaning pins and the manual. | ||
= Trouble Shooting = | = Trouble Shooting = | ||
| − | + | TBD | |
= History and Ownership = | = History and Ownership = | ||
| − | |||
| − | |||
| − | |||
Bought late 2021; owned by the space. | Bought late 2021; owned by the space. | ||
| − | |||
| − | |||
Huidige versie van 12 okt 2021 om 22:01
This equipment is Noise Category 3: Can be used at all hours. No limits.
This equipment is safety category 4:
- In-person, instructions strongly advised but not mandatory.
- Reading, and following, the instructions on the Wiki is mandatory!
Located at the soldering bench
Risks
Beware that you are handling molten metal. Consider wearing safetyglasses if things are likely to splatter.
Dont leave the machine turned on for a long time, the nozzle will corrode.
Manual / use
Manual in English and in Nederlands
Short list with the key points for usage, read the manual for the complete instructions.
- Turn on the device by pressing the red button.
- Select the temperature by pressing up/down buttons. Beware of the different between Celsius and Kelvin.
- Put the nozzle over the pin that should be cleaned and let the solder melt.
- Pull the trigger to suck the molten solder from the pin.
- After use the gun should be cleaned by sucking clean for a few times (3-5). Also use the cleaning pins to clean the nozzle, after using those pins also suck the residual solder from the nozzle. Solder that is left in the nozzle will damage the nozzle.
Maintenance
After every usage the nozzle should be cleaned with a cleaning pin.
The glass tube should be emptied once in a while, read the manual for instructions how to do this.
There is a box with extra cleaning pins and the manual.
Trouble Shooting
TBD
History and Ownership
Bought late 2021; owned by the space.
| Datum | Comment |
| September 2021 | Bought from Eleshop by the Makerspace. |
