Vlakbank

This equipment is safety category 1 - the most dangerous class of machines.

Mandatory instruction is required.

The [liability waiver] needs to be on file and approval from the trustees is required (post instruction).
Two people present at all times.
Can only be used between 07:00 and 19:00 because of noise.

This equipment is safety category 1 - the most dangerous class of machines.
Mandatory instruction is required.
The [liability waiver] needs to be on file and approval from the trustees is required (post instruction).
Two people present at all times.
Can only be used between 07:00 and 19:00 because of noise.

This equipment is safety category 1 - the most dangerous class of machines.
Mandatory instruction is required.
The [liability waiver] needs to be on file and approval from the trustees is required (post instruction).
Two people present at all times.
Can only be used between 07:00 and 19:00 because of noise.

This equipment is safety category 1 - the most dangerous class of machines.
Mandatory instruction is required.
The [liability waiver] needs to be on file and approval from the trustees is required (post instruction).
Two people present at all times.
Can only be used between 07:00 and 19:00 because of noise.

This equipment is safety category 1 - the most dangerous class of machines.
Mandatory instruction is required.
The [liability waiver] needs to be on file and approval from the trustees is required (post instruction).
Two people present at all times.
Can only be used between 07:00 and 19:00 because of noise.

This equipment is safety category 1 - the most dangerous class of machines.
Mandatory instruction is required.
The [liability waiver] needs to be on file and approval from the trustees is required (post instruction).
Two people present at all times.
Can only be used between 07:00 and 19:00 because of noise.

This equipment is Noise Category 1: can only be used between 07:00 and 19:00.
Wear hearing protection.

This equipment is Noise Category 1: can only be used between 07:00 and 19:00.
Wear hearing protection.

This equipment MUST be used with active dust control:

• Connect a shop-vac prior to use and keep it on while using it.
• Let it run for 10-20 seconds post use.

Not doing so endangers the operator, others, the space and the equipment.

Regarding the GroteStofAfzuiger:

• Do not fill the bag past 2/3rd of its capacity.
• Check for enough airflow before using the connected tool.
• Check that there is no (hot/smoldering) wood in the bottom of the machine when you smell something.

Intro

Dit is met stip het meest gevaarlijke apparaat van de space.

Sluit altijd de GroteStofAfzuiger altijd - want anders kan het hout zich onderop ophopen en gaan smeulen. Dat hebben we al eens geprobeerd - en was niet fijn.

Access control

This node is under NodeVlakbank control. Swipe your badge; then press the green button on the safety contactor to turn it on.

Press the red button on the safety contactor to turn it off.

Na gebruik

1. Machine geod schoonmaken; ook van binnen.
2. Check dat de zak van de GroteStofAfzuiger niet meer dan half vol is - indien wel - leeg deze dan (zie instructies]).

Messen

De messen zijn relatief kwetsbaar. Zorg er dus voor dat je absoluut geen hout hebt met spijkers of andere zaken. Dan komen er happen/bramen in. Dit kan ook gebeuren bij normaal gebruik.

Meld het onmiddelijk als je ziet dat er een hapje uit is - zodat de volgende persoon zijn hout niet ruinieerd.

Er zijn 5 Messen van 300 x 3mm x 26mm (reeds 6_ maal geslepen) en twee sets nieuwe messen. De 2 sets van 3 nieuwe messen waren 300x35x3 bij aankoop (2018-11).

Set	Geslepen	Geschiedenis
1	6 maal geslepen	5 messen; medio 2017 en 2018 geslepen
2	3stuks, nieuw 2018/10	Nog niet in gebruik
3	3stuks, nieuw 2018/10	Nog niet in gebruik

Standaard [HSS VOOR 300X35X3] ziijn rond de 20 euro/stuk. Slijpen kost rond de 7 euro per mes bij [Slijperij Vlijm] op de Flevoweg (achter de Gamma).

Wat te doen als ik een mes kapot maak

Dat is niet erg - en kan bij normaal gebruik gebeuren. Meld het in elk geval meteen op de deelnemerslijst. Zodat de volgende persoon zijn hout niet ruinieerd.

Als het komt doordat je een spijker geraakt hebt, of als je een veelgebruiker bent, of met erg hard hout werkt - dan mag je schuldgevoel natuurlijk afkopen door de messen te laten slijpen, door nieuwe te doneren of door 15-25 euro in de pot te stoppen.

Safety

The safety of the jointer can be improved by using two different devices:

• the built-in blade guard;
• push blocks.

The blade guard must be positioned so that it covers the length of the rotating blades left unused. Never set the blade guard fully aside.

Push blocks act as another layer between your hands and the blades and increase the distance between your hands and the blades. Use them whenever possible, especially when squaring stock. When jointing a sheet, use one block to push the sheet against the fence. Push blocks should never touch the blades, only the stock.

Jointer push blocks

Kick-back

You can reduce chances of kick-back (when your stock has knots, for instance) by taking lighter passes. Change the depth of the cut using the lever on the right side of the machine.

The harder the wood, the higher the chances of kickback.

Kick-back can happen even when taking all necessary precautions, be as careful as you can, but be aware things can and will go wrong. The best way to not get hurt is to not use it if you don't need it.

General rules

Lighter passes help reducing wear on the blades and will give you a better surface.

Make sure you have enough space to process your stock, both on the in-feed side and out-feed side of the machine, and that your way is fully cleared. A good thing to do is to rehearse the cut you are about to make before turning the machine on:

• where are your hands and feet located?
• how do you hold the stock?
• are your hands very close to the blades, can you avoid it?
• do you have to bend over the surface?
• what do you do once you have completed your cut?
• do you really need to leave the machine on after your cut and if so, is the blade guard covering the blades?

Your attention decreases greatly when performing the same task over and over. This is when most accidents happen, even for experienced woodworkers. Try to remember that every cut is as dangerous as the previous one.

Process only solid wood free of nails and screws. Man-made materials like plywood are bad for the blades.

History

Datum	Wie	Wat
21/10/2018	DirkWillem	Nieuwe messen besteld.
28/10/2018	DirkWillem	Nieuwe 300x35x3 messen op space. HansD gaat ze er in zetten.
28/10/2018	DirkWillem	Alle bestelde 300x35x3 HSS messen aangekomen.