3D Scanner: verschil tussen versies
(31 tussenliggende versies door 3 gebruikers niet weergegeven) | |||
Regel 1: | Regel 1: | ||
− | [[Category:CNC]][[Category:SafetySheet]][[Category:Tool]][[Category: | + | [[Category:CNC]][[Category:SafetySheet]][[Category:Tool]][[Category:Measuring]] |
− | |||
− | = | + | = OUT OF ORDER = |
− | We have a 3D scanner based on a Microsoft XBox Kinekt device, the [[https://skanect.occipital.com | + | One of the protective lens covers has a crack. Being fixed (I took HDMI cable too) (dirkx/2021-05-30) |
+ | |||
+ | [[Bestand:Kinnectdeelnemer.JPG|miniatuur|]] | ||
+ | |||
+ | We have a 3D scanner based on a Microsoft XBox Kinekt device, the [[https://skanect.occipital.com Skanect]] software and a Mac Mini. | ||
+ | |||
+ | = Still to do = | ||
+ | |||
+ | # Write better manual | ||
= Instructions for use = | = Instructions for use = | ||
* Log in as Guest | * Log in as Guest | ||
− | * Start the | + | * Start the Scanekt Software (in /Applications) vierkante smiley dan opent nieuw scherm, linkerbalk vind je applications, en kies dan skanect |
− | * Configure for a BOX scan (1x1 is about righ). | + | * Configure for a BOX scan (1x1 is about righ for a think - 3x3 for a person).(kies object of body) |
− | * Go through each of the steps. | + | * Go through each of the steps in Scannekt. |
− | * Save the resulting file (PLY) to a USB disk | + | * resultaat kan je bewaren als .stl (share, export model) |
+ | * Save the resulting file (PLY) to a USB disk or SD card (slot is on the back, left hand side) | ||
+ | |||
+ | == Maintenance == | ||
+ | |||
+ | Check, every 2-3 months, of all updates ran. | ||
+ | |||
+ | == Reinstall from 'zero' == | ||
+ | |||
+ | See [[3D Scanner - installation notes]] for more information. | ||
== Ownership == | == Ownership == | ||
− | The Mac Mini, Kinekt and PSU are owned by Dirk-Willem van Gulik (zie | + | The Mac Mini, Kinekt and PSU are owned by Dirk-Willem van Gulik (zie [[:Category:OnLoan]]) and to be '''kept at the makerspace''' at all times. No exceptions. |
+ | |||
+ | The UK/NL adapter was donated by Hans. The screen, HMDI/DVI cable and mouse were donated by Hans Beerman. | ||
== Usage == | == Usage == | ||
Regel 22: | Regel 40: | ||
{{SafetyCat5}} | {{SafetyCat5}} | ||
{{NoiseCat3}} | {{NoiseCat3}} | ||
+ | {{InBruikleen|naam=Dirk-Willem}} |
Huidige versie van 30 mei 2021 om 21:26
Inhoud
OUT OF ORDER
One of the protective lens covers has a crack. Being fixed (I took HDMI cable too) (dirkx/2021-05-30)
We have a 3D scanner based on a Microsoft XBox Kinekt device, the [Skanect] software and a Mac Mini.
Still to do
- Write better manual
Instructions for use
- Log in as Guest
- Start the Scanekt Software (in /Applications) vierkante smiley dan opent nieuw scherm, linkerbalk vind je applications, en kies dan skanect
- Configure for a BOX scan (1x1 is about righ for a think - 3x3 for a person).(kies object of body)
- Go through each of the steps in Scannekt.
- resultaat kan je bewaren als .stl (share, export model)
- Save the resulting file (PLY) to a USB disk or SD card (slot is on the back, left hand side)
Maintenance
Check, every 2-3 months, of all updates ran.
Reinstall from 'zero'
See 3D Scanner - installation notes for more information.
Ownership
The Mac Mini, Kinekt and PSU are owned by Dirk-Willem van Gulik (zie Category:OnLoan) and to be kept at the makerspace at all times. No exceptions.
The UK/NL adapter was donated by Hans. The screen, HMDI/DVI cable and mouse were donated by Hans Beerman.
Usage
This equipment is safety category 5: Equipment that is relatively fragile or expensive
- In person instructions is not mandatory.
- Reading the wiki, and following the instructions, is mandatory.
This equipment is Noise Category 3: Can be used at all hours. No limits.
Dit gereedschap is van Dirk-Willem en in bruikleen gegeven aan de Space.
Let bij het gebruik op de extra regels.