Grote Gaten Zaag - Large Hole Saw: verschil tussen versies
(→Speed) |
|||
| (9 tussenliggende versies door dezelfde gebruiker niet weergegeven) | |||
| Regel 1: | Regel 1: | ||
{{SafetyCat6}} {{NoiseCat3}} | {{SafetyCat6}} {{NoiseCat3}} | ||
| − | [[Category:Tool]][[Category:Wood]][[Category:Small]] | + | [[Category:Tool]][[Category:Wood]][[Category:Small]][[Categorie:Boren]] |
There are is a set of large hole saws in the workshop. | There are is a set of large hole saws in the workshop. | ||
| Regel 7: | Regel 7: | ||
[[Bestand:largeholesaw-box.jpg|miniatuur]] | [[Bestand:largeholesaw-box.jpg|miniatuur]] | ||
| − | See also the [[HSS Drills]] and [[Wood Drills]] for general purpose drilling and [[Spade drills]] for larger holes. | + | See also the [[HSS Drills]] and [[Wood Drills]] for general purpose drilling and [[Spade drills]] for larger holes. Or the [[Step-drill/getrapte boor]] for thin sheets and the [[Large HSS drills]]. |
| + | |||
| + | You need to make sure sawdust does not build up - you'll burn the wood otherwise. | ||
| + | |||
| + | === Saw dust problems === | ||
| + | |||
| + | It is often a good idea to first drill a hole (8-12mm) just inside (if you are making a hole) or outside (if you are making a disk) circle you are going to saw. This lets the sawdust escape. | ||
| + | |||
| + | [[Bestand:largeholesaw-escape.png]] | ||
| + | |||
== Speed == | == Speed == | ||
| − | [[Bestand:Saw-speed-table.png| | + | [[Bestand:Saw-speed-table.png|600px|typical speeds for larger sizes]] |
| − | |||
| − | |||
== Location == | == Location == | ||
| Regel 27: | Regel 34: | ||
== Ownership & History == | == Ownership & History == | ||
| − | Owned by the space. Current set bought | + | Owned by the space. Current set bought early May 2019. |
| − | The doorn and the 44mm saw where replaced 2019-11-12; as they broke. Metal fatique. | + | The doorn and the 44mm saw where replaced 2019-11-12; as they broke. Metal fatique. New model fancier (15 euro level). |
Huidige versie van 8 mei 2023 om 16:01
This equipment is safety category 6: Other equipment with no limits.
This equipment is Noise Category 3: Can be used at all hours. No limits.
There are is a set of large hole saws in the workshop.
See also the HSS Drills and Wood Drills for general purpose drilling and Spade drills for larger holes. Or the Step-drill/getrapte boor for thin sheets and the Large HSS drills.
You need to make sure sawdust does not build up - you'll burn the wood otherwise.
Saw dust problems
It is often a good idea to first drill a hole (8-12mm) just inside (if you are making a hole) or outside (if you are making a disk) circle you are going to saw. This lets the sawdust escape.
Speed
Location
Usually above the wood-workbench on the side of the pillar dril/mitre saw.
Maintenance / Replacing
These tools will wear out - and the space will replace them.
Ask on the mailing lists to get them ordered.
Ownership & History
Owned by the space. Current set bought early May 2019.
The doorn and the 44mm saw where replaced 2019-11-12; as they broke. Metal fatique. New model fancier (15 euro level).
